Output Terminal Assignments; My Function Input Setting Assignments, And Parameter/Input - Toshiba H9 ASD Installation And Operation Manual

Table 8. Output Terminal Assignments, My Function Input Setting Assignments, and Parameter/Input
Setting Numbers for the FLA/B/C, O1A/O1B (OUT1), O2A/O2B (OUT2), OUT3 – OUT6, and R1 – R4.
Input Param.
Setting Setting
1000 0 Lower-Limit Frequency
1002 2 Upper-Limit Frequency
1004 4 Low-Speed Signal
1006 6 Acceleration/Deceleration Completion
1008 8 Speed Reach Signal
1010 10 Failure FL (All Trips)
1012 12 Failure FL (Except EF, OCL, EPHO, OL2)
1014 14 Over-Current (OC) Alarm
1016 16 ASD Overload (OL1) Alarm
1018 18 Motor Overload (OL2) Alarm
1020 20 Over-Heat Alarm
1022 22 Over-Voltage Alarm
1024 24 Main Circuit (MOFF) Under-Voltage Alarm
1026 26 Low-Current Alarm
1028 28 Over-Torque Alarm
1030 30 DBR Overload Alarm
1032 32 Emergency Off Active
1034 34 Retry Active
1036 36 Pattern Operation Switching Output
1038 38 PID Deviation Limit
1040 40 Run/Stop
1042 42 Serious Failure (OCA, OCL, EF, Phase Failure, etc.) 1130
1044 44 Light failure (OL, OC1, 2, 3, OP)
1046 46 Commercial Power/ASD Switching Output 1
1048 48 Commercial power/ASD switching Output 2
1050 50 Cooling Fan On/Off
1052 52 Jogging Operation Active (Jog Run Active)
1054 54 Panel/Terminal Board Operation Switching
1056 56 Cumulative Run-time Alarm
1058 58 ProfiBus/DeviceNet/CC-Link Communication Error 1232
1060 60 Forward/Reverse Switching
1062 62 Ready for Operation 1
1064 64 Ready for Operation 2
1068 68 Brake Release (BR)
1070 70 Alarm Status Active
1072 72 Forward Speed Limit (Torque Control)
1074 74 Reverse Speed Limit (Torque Control)
1076 76 ASD Healthy Output
1078 78 RS485 Communication Error
1080 80 Error Code Output 1
1082 82 Error Code Output 2
1084 84 Error Code Output 3
Note: Only positive logic is available for the listed parameters.
H9 ASD Installation and Operation Manual
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.ctiautomation.net - Email: info@ctiautomation.net
Discrete Output Terminal Assignment Selections
Function
Input Param.
Setting Setting
1086 86 Error Code Output 4
1088 88 Error Code Output 5
1090 90 Error Code Output 6
1092 92 Specified Data Output 1
1094 94 Specified Data Output 2
1096 96 Specified Data Output 3
1098 98 Specified Data Output 4
1100 100 Specified Data Output 5
1102 102 Specified Data Output 6
1104 104 Specified Data Output 7
1106 106 Light Load
1108 108 Heavy Load
1110 110 Positive Torque Limit
1112 112 Negative Torque Limit
1114 114 External Rush Suppression Relay Activated
1118 118 Completion of Stop Positioning
1120 120 L-STOP
1122 122 Power Failure Synchronized Operation
1124 124 Traverse in Progress
1126 126 Traverse Deceleration Active
1128 128 Part Replacement Alarm
130 Over-Torque Alarm
1132 132 Frequency Command ½ Selection
1134 134 Failure FL (Except Emergency Off)
1222 222 My Function Output 1
1224 224 My Function Output 2
1226 226 My Function Output 3
1228 228 My Function Output 4
1230 230 My Function Output 5
232 My Function Output 6
1234 234 My Function Output 7
1236 236 My Function Output 8
1238 238 My Function Output 9
1240 240 My Function Output 10
1242 242 My Function Output 11
1244 244 My Function Output 12
1246 246 My Function Output 13
1248 248 My Function Output 14
1250 250 My Function Output 15
1252 252 My Function Output 16
1254 254 Always Off
Function
239