Sanyo DC-F21 Instruction Manual page 14

liiii
PERATION
(using the rem
Using the on/off timer
Set the on and off times, function to be used and volume level. Operation
will start with the selected function at the on time, The sound will be
gradually increased from a no-sound level to the volume setting (fade-in).
The power will be switched off at the off time.
The on/off timer will function every day unless it is released.
Preparation
Note:
Make absolutely sure that the clock is set to the correct time before setting
the timer.
Select the function for timer operation and prepare the sources to be
used.
If the function selected is tuner, tune in to the desired band and
station.
Adjust the volume level as desired.
Operation
1.
2,
3.
4.
5.
6.
Press the TIMER button.
TIMER
l—f t—f j—l ON
For AU: The clock ia 12-hour
l_l l_l l_l
display. Example: AM 12:00
The previous timer on time setting appears.
Press the ADJUST button within 10 seconds.
\l/
\l/
TIMER
1—1 1—1 1—[ ON
Iu u Iu
/l\
Set the timer on time by pressing the + or – TIME SET button, then
press the ADJUST button (as described under "ADJUSTING THE
CLOCK).
,1/
\l/
\l/
\l/
TIMER
t—l t—l 1—1 ON
l—l —1 l—l
TIMER
OFF
I l_l I_l
/l\
I 3 l_l
/l\
The timer off time setting appears.
Set the timer off time as described in step 3.
\l/
\l/
TIMER
\l/
13 II l—l
OFF
1— -n
TIMER
I_l J u
/l\
L u
The current function appears.
If you wish to change the function, press the FUNCTION button
on the front panel to select the desired function.
Press the ADJUST button.
The original display returns, then the timer operation standby mode is
activated. "TIMER remains lit.
Press the CL/ON button to switch off the power.
For tape playback, press the PLAY button on the front panel (Deck
A or Deck B).
For unattended recording, press the REC button on the front
panel.
"TIMER" blinks during a timer controlled operation.
To switch off the power during a timer controlled operation, press the
A /ON button. The timer will be set in the standby mode.
To check the timer settings
Press the TIMER button repeatedly. The timer settings are displayed in
the following order:
On time
Off time
Function
Original display returns
To change the settings, press the TIMER button to select the setting to be
changed, then press the ADJUST button so that the display blinks.
Change the setting as explained above.
To release the timer
After turning the power on, press the TIMER button, then press the SET/
CLEAR.
To set the timer again with the same settings
1, Press the TIMER button, then press the SET/CLEAR.
2. Press the O /ON button to switch off the power.
Note:
If the SET/CLEAR button is pressed while the timer is being set, the
original display returns.
The timer mode is released if a power failure occurs during timer
controlled operation.
The timer may not operate if a power failure occurs during timer
operation standby mode.
Using the sleep timer
The sleep timer automatically switches off the power after a preset time
has elapsed. The volume will gradually be reduced (fade-out) during the
l-minute period before the unit turns off. There are 12 time periods
available: 120, 110, 100, 90, 80, 70, 60, 50, 40, 30, 20, and 10 minutes.
Press the SLEEP button repeatedly to select the desired sleep time.
"SLEEP and the selected time blink on the display. After several seconds,
the original display returns. "SLEEP" blinks.
To check the remaining sleep time
Press the SLEEP button. The remaining time is displayed. After several
seconds, the original display returns.
To release the sleep timer while in operation
Press the SLEEP button, then press the SET/CLEAR. The timer is also
released if the power is switched off.
13