Gehl RS5-19 Operator's Manual page 21

B - Scroll Button: Pressing this button changes the
function displayed in the multi-function display
screen.
Press and hold the button in for 3 seconds to tog-
gle the engine coolant tmperature reading between
celsius and fahrenheit.
A1 - Fuel Level Gauge: The fuel level is displayed at
all times in the lower portion of the display. It indicates
the amount of fuel remaining in the fuel tank.
A2 - Engine Coolant Temperature: Press button "B"
until "TEMP" is displayed. It indicates the temperature
of the engine coolant. Under normal conditions, this
should indicate approximately 185°F (85°C).
A3 - Engine Speed: Press button "B" until "RPM" is
displayed. This indicates the engine speed.
A4 - Voltmeter: Press button "B" until "VOLTS" is
displayed. This indicates the voltage output from the
alternator.
A5 - Hourmeter: Press button "B" until "HRS" is dis-
played. It indicates the total operating time of the
machine and should be used for keeping the mainte-
nance log.
A6 - Maintenance Reminder: After every 250 hours
a reminder will display: "ROUTINE MAINTENACE
IS REQUIRED ⎯ CHECK OPERATOR'S MANU-
AL." Perform the required maintenance, and then clear
the message by pressing and holding button "B" until
the message is cleared.
NOTE: The maintenance reminder message
must display at least three minutes before it can
be cleared by pressing and holding button "B".
A7 - Error Fault Code: Error codes and a short error
description are displayed in this screen. The error code
will clear when the error is corrected.
A8 - DPF Regeneration: If the auto regen has been
disabled or an auto regen is in process, a message will
be displayed indicating the need for a DPF regenera-
tion along with the level of regeneration needed as
"LOW", "MEDIUM" OR "HIGH".
Indicator Lamps
C - Engine Failure: This lamp when lit, alerts the
operator of a fault condition. Refer to the multi-func-
tion display screen for error codes.
D - Engine Oil Pressure Lamp: This lamp indicates
when the engine lubricating oil pressure is too low.
During normal operation, with the engine running, this
PRINTED IN U.S.A.
lamp should be off. During starting and when the igni-
tion is on but the engine is not running, this lamp will
be on.
IMPORTANT: If this lamp comes on during nor-
mal operation, stop the engine immediately! After
allowing the oil to drain down for a few minutes,
check the engine oil level. Maintain oil level at the
FULL mark on the dipstick.
E - Engine Coolant Temperature Lamp: This lamp
indicates when the temperature of the engine coolant is
too high.
IMPORTANT: If this lamp comes on during nor-
mal operation with the engine running, STOP the
engine as soon as possible and check the engine
cooling system.
F - Alternator Lamp: This lamp indicates the condi-
tion of the electrical charging system. During normal
operation, this lamp should be off. If the charge rate is
too high or too low, this lamp will come on.
G - Air Cleaner Restriction Indicator Lamp: If this
lamp comes on, the engine air filter requires service.
H - Engine Pre-heat Indicator Lamp: When lighted
this lamp indicates that the cold weather starting aid is
in use.
I - Hydrostatic Transmission Oil Temperature
Lamp: This lamp indicates when the temperature of
the transmission oil is too high. During normal opera-
tion this lamp should be off, indicating that the trans-
mission oil system is at the proper temperature.
IMPORTANT: If this lamp comes on during nor-
mal operation, a problem may exist in the trans-
mission oil system. Stop the machine immediate-
ly and investigate the cause of the problem!
J - Low Fuel Lamp: This lamp indicates a low fuel
situation. The fuel tank should be filled as soon as pos-
sible.
K - Hydraulic Oil Filter Restriction Lamp: If this
lamp comes on, the hydraulic oil filter requires service.
19
50960066/AP0813