Related Manuals for Kipor Sinemaster IG2600
Summary of Contents for Kipor Sinemaster IG2600
- Page 1 WUXI KIPOR POWER CO., LTD. S I N E M A S T E R DIGITAL INVERTER GENERATOR I G 2 6 0 0 I G 2 6 0 0 h...
- Page 2 PREFACE 12. SKETCH MAP Thank you for purchasing our generators. This manual covers operation and maintenance of the IG2600, IG2600h IG2600h generator. All information in this publication is based on the latest product information available at the time of approval for printing. We reserve the right to make changes at any time without notice and without incurring any obligation.
-
Page 3: Table Of Contents
11. SPECIFICATIONS CONTENTS Model IG2600/IG2600h Rated frequency (Hz) Rated voltage (V) 1. Safety Instructions Rated current (A) 19.5 Rated speed (rpm) 3600 2. Safety Label Locations Rated output (kVA) Max output (kVA) 3. Component Indentificaction DC output 4. Pre-operation Check DC voltage 12V-8.3A Electric circuit breaker... -
Page 4: Safety Instructions
Appliance does not operate: 1. SAFETY INSTRUCTIONS Is the output indicator light ON? Our generators are designed to give safe anddepend- W A R N I N G able service if operated according to instructions. Read and understand the Owner's Manual before op- Is the overload Take the generator to an erating the generator. - Page 5 To ensure safe operation-- 10.TROUBLESHOOTING Gasoline is extremely flammable and explosive under W A R N I N G certain conditions. Refuel in a well ventilated area with the engine stopped. Keep away from cigarette, smoke and sparks when re- When the engine will not start: fueling the generator.
-
Page 6: Safety Label Locations
a. Drain all gasoline from the fuel tank into an approved gasoline container. 2. SAFETY LABEL LOCATIONS b. Turn the engine switch ON, and loosen the carburetor drain screw and drain the gasoline from the carburetor into a suitable container. c. -
Page 7: Component Identification
3.COMPONENT IDENTIFICATION 9.TRANSPORTING/STORAGE To prevent fuel spillage when transporting or during temporary storage, the genera- Chock Lever tor should be secured upright in its normal operating position, with the engine swith Fuel Cap Lever OFF. Turn the cap lever fully counterclockwise to the "OFF" position. Fuel Filler Cap W A R N I N G When transporting the generator:... -
Page 8: Control Panel
4.SPARK ARRESTER MAINTENANCE(Equipped type only) Control panel W A R N I N G If the generator has been running, the muffler will be very hot. Allow it to cool before proceeding. Output Indicator Light 1.Remove the four 5mm screws, and remove the muffler protector. Smart Throttle Switch Overload Indicator Muffler Protector... - Page 9 SMART throttle 5.Visually inspect the spark plug. Discard it if the insulator is cracked or chipped. Clean the spark plug with a wire brush if it is to be reused. Engine speed is kept at idle automatically when the electrical appliance is discon- 6.Measure the plug gap with a feeler gauge.
-
Page 10: Pre-Operation Check
3.SPARK PLUG SERVICE 4.PRE-OPERATION CHECK RECOMMENTED SPARK PLUG: R6-388 To ensure proper engine operation, the spark plug must be properly gapped and CAUTION Be sure to check the generator on a level surface with free of deposits. the engine stopped. 1.Remove the spark plug maintenance cover. -
Page 11: Starting The Engine
The Low Oil Alarm System will automatically stop the engine before the oil level Wash your hands with soap and water after handling used oil. Note: Note: falls below the safe limit. However, to avoid the inconvenience of an unexpected NOTE Please dispose of used motor oil in a manner that is shutdown, it is still advisable to visually inspect the oil level regularly. - Page 12 1.CHANGING OIL 3.Check the air cleaner. Check the air cleaner element to be sure it is clean and in good condition. Loosen the cover screw and remove the left side maintenance cover. Press the Drain the oil while the engine is still warm to assure rapid and complete draining. latch tab on the top of the air cleaner body, remove the air cleaner cover, check the Make sure to turn the engine switch and the fuel cap CAUTION...
-
Page 13: Starting The Engine
(1) Log hours of operation to determine proper maintenance. NOTE: START (2) Service more frequently when used in dusty areas. (3) These items should be serviced by an authorized KIPOR dealer, unless the owner has the proper tools and is mechanically proficient. See the KIPOR Shop Manual. - Page 14 3.Turn the cap lever fully counterclockwise to the "OFF" position NOTE Do not use the choke when the engine is warm or the air temperature is high. 4.Pull the starter grip until resistance is felt, then pull the starter grip briskly toward the arrow as shown below.
-
Page 15: High Altitude Operation
1.Switch off the connected equipment and pull the inserted plug. generator at altitudes higher than 1,500 m(5,000 feet) above sea level, have your authorized KIPOR dealer perform these carburetor modifications. Even with suitable carburetor jetting, engine horsepower will decrease approximately 3.5% for each 305m (1,000 feet) increase in altitude. -
Page 16: Generator Use
Low oil alarm system 6.GENERATOR USE The Low Oil alarm system is designed to prevent engine damage caused by an insufficient amount of oil in the crankcase. Before the oil level in the crankcase falls below a safe limit, the Low oil alarm system will automatically shut down the engine (the engine switch will remain in the ON position). - Page 17 NOTE W A R N I N G The battery gives off explosive gases; keep sparks, The DC receptacle can be used while the AC power flames and cigarettes away. Provide adequate venti- is in use. if you use both at the same time, be sure lation when charging.
- Page 18 If the overload indicator light (red) stays on, Do not attempt to start an automobile engine with the CAUTION consult your KIPOR generator dealer. generator still connected to the battery. The generator may be damaged. Connect the positive battery terminal to the positive charging cord.
- Page 19 1.Connect the ground terminal. Earth Mark AC Receptacle Ground Terminal 4.Switch on the equipment to be used. in case of overload operation or when trouble occurs for the equipment being used, the output indicator light(green) will go out, the overload indicator light(red) will light continuously, and no power will be put out.
Need help?
Do you have a question about the Sinemaster IG2600 and is the answer not in the manual?
Questions and answers