Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DeWalt D27105
Summary of Contents for DeWalt D27105
- Page 1 D27105 D27105V www.
- Page 2 Copyright D WALT...
- Page 3 13 17...
- Page 4 35 36 38 37...
- Page 8 77 78...
- Page 10 102 101 3-8mm...
- Page 13 90° 45° 0 ° - 4 5 °...
-
Page 15: Technical Data
E N G L I S H FLIP-OVER SAW D27105, D27105V Congratulations! Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and You have chosen a D WALT tool. Years of experience, thorough product... -
Page 16: Safety Instructions
E N G L I S H Safety Instructions 16. Remove adjusting keys and wrenches. Form the habit of checking to see that adjusting keys and wrenches are WARNING! When using electric tools basic safety precautions removed from the tool before operating the tool. should always be followed to reduce the risk of fire, electric shock and personal injury 17. - Page 17 E N G L I S H • Never operate the saw without the upper and lower guards in place. • Do not use saw blades with a body thickness greater or a width of tooth smaller than the thickness of the riving knife. •...
-
Page 18: Markings On Tool
E N G L I S H Markings on Tool Description (fi g. A1 - A11) The following pictograms are shown on the tool: 1 On/off switch (saw bench mode) 2 Table release lever Read instruction manual before use. 3 Rotating table clamp 4 Mitre saw table 5 Rotating table Wear ear protection. -
Page 19: Electrical Safety
Your D WALT D27105 flip-over saw has been designed to operate as a WARNING! Do never operate this machine when it is not mitre saw or a saw bench to perform the four main sawing operations of fastened to the workbench. - Page 20 E N G L I S H Assembly for mitre saw mode Checking and adjusting the blade to the fence (fi g. H1 - H3) • Loosen the mitre knob (79) and depress the mitre latch (80) to release the rotating table (5) (fi g. H1). Mounting the under-table guard (fi...
- Page 21 E N G L I S H • If adjustment is required, proceed as follows: • Holding the guard vertically, align the slot in the rear of the guard with • Turn the bevel position adjustment stop screw (95) in or out as the riving knife.
-
Page 22: Operation
E N G L I S H • Tighten the knob (117). - extra safety: the hinged safety enclosure plate (123) can be locked by • Check that the pointer (120) indicates zero on the scale (121). passing a padlock through the holes (124 & 125). The plate also serves Adjust if necessary. - Page 23 E N G L I S H • Loosen the fence clamping knob (91) and slide the upper part of the Outside corner side fence to the left as far as it will go. - Left side • Loosen the bevel clamp knob (17) and set the bevel as desired. •...
-
Page 24: Optional Attachments
E N G L I S H Roller support table (fi g. A6) • After completing the cut, switch the machine off, allow the saw blade to stop and remove the workpiece. The roller support table (40) is used to support long workpieces. In mitre saw mode, the roller support table can be mounted on the left-hand side WARNING: Never push or hold the free or cut-off side of the or on the right-hand side, or with two sets on either side. -
Page 25: Optional Accessories
E N G L I S H • Loosen the screw (140) of the adjustment cam (141). WALT provides a facility for the collection and recycling of D WALT products once they have reached the end of their working life. To take •... - Page 26 Türkiye KALE Hırdavat ve Makina A.Ş. Tel: 0212 533 52 55 Defterdar Mah. Savaklar Cad. No:15 Faks: 0212 533 10 05 Edirnekapı / Eyüp / İSTANBUL 34050 TÜRKİYE www.dewalt.com.tr United Kingdom WALT Tel: 01753-56 70 55 210 Bath Road Fax:...