DeWalt DC927-XE Instruction Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Drill
  5. DC927-XE
  6. Instruction manual
DeWalt DC927-XE Instruction Manual

DeWalt DC927-XE Instruction Manual

Heavy-duty 13 mm (1/2") cordless hammerdrill
Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTRUCTION MANUAL
DC927-XE
HEAVY-DUTY 13 MM (1/2") CORDLESS HAMMERDRILL

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DC927-XE

Summary of Contents for DeWalt DC927-XE

  • Page 1 INSTRUCTION MANUAL DC927-XE HEAVY-DUTY 13 MM (1/2") CORDLESS HAMMERDRILL...

  • Page 3: Definitions: Safety Guidelines

    1. WORK AREA Definitions: Safety Guidelines a. Keep work area clean and well lit. Cluttered and dark areas invite accidents. b. Do not operate power tools in explosive atmospheres, such as in the The definitions below describe the level of severity for each signal presence of flammable liquids, gases or dust.
  • Page 4 c. Avoid accidental starting. Ensure the switch is in the off position before g. Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, plugging in.

  • Page 5: Extension Cords

    • Young children and the infirm. This appliance is not intended for use by • Wear ear protectors when hammering for extended periods of time. Prolonged young children or infirm persons without supervision. Young children should be exposure to high intensity noise can cause hearing loss. Temporary hearing loss supervised to ensure that they do not play with this appliance.

  • Page 6: Important Safety Instructions For All Battery Packs

    • Charge the battery packs only in D WALT chargers. WARNING: ALWAYS wear proper personal hearing protection that conforms to • DO NOT splash or immerse in water or other liquids. ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise •...

  • Page 7: Important Safety Instructions For All Battery Chargers

    Important Safety Instructions for all Battery Chargers b. and the battery liquid gets into your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. (Medical note: SAVE THESE INSTRUCTIONS: This manual contains important safety and operating The liquid is 25-35% solution of potassium hydroxide.) instruc tions for battery chargers.

  • Page 8: Charging Procedure

    • When operating a power tool outdoors, use an extension cord suitable for weekly or after 10 charge/discharge cycles or whenever the pack no longer delivers outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric the same amount of work.

  • Page 9: Charge Indicators

    Indicator Light Operation before use. A battery pack may also slowly lose its charge if left in a charger that is not plugged into an appropriate AC source. WEAK BATTERY PACKS: Chargers can also detect a weak battery pack. Such batteries are still usable but should not be expected to perform as much work.

  • Page 10: Key Features And Functions

    The center position of the control button locks the tool in the OFF position. When WARNING: Shock hazard. Don’t allow any liquid to get inside charger. Electric changing the position of the control button, be sure the trigger is released. shock may result.

  • Page 11: Operation

    2. Rotate the mode control collar (C) so the screw symbol is aligned with the arrow. WARNING: Always ensure the bit is secure before starting the tool. A loose bit 3. Set the torque adjustment collar (D) to the appropriate number setting for the may eject from tool causing possible personal injury.

  • Page 12: Side Handle

    Installing and Removing the Battery Pack (Fig. 8, 9) Drill Operation NOTE: Make sure your battery pack is fully charged. 1. Select the desired speed/torque range using the gear shifter to match the speed and torque to the planned operation. CAUTION: Make certain the lock-off button (B), as shown in Figure 1, is engaged 2.

  • Page 13: Maintenance

    adjustment collar (D) to the desired setting. Make a few practice runs in scrap or Recommended accessories for use with your tool are available at extra cost from unseen areas to determine the proper position of the clutch collar. your local service center. If you need any assistance in locating any accessory, please contact D WALT Industrial Tool Co., 20 Fletcher Road, Mooroolbark, VIC 3138 MAINTENANCE...
  • Page 14 FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call (AUS) 1800 654 155 or (NZ) 09 259 1111 for a free replacement. HEAVY DUTY 13mm (1/2") DC927-XE CORDLESS DRILL/DRIVER/HAMMERDRILL WARNING: To reduce the risk of injury, user must read and understand instruction manual.
  • Page 16 WALT BATTERY AND CHARGER SYSTEMS Battery Output Chargers/Charge Time Nominal 240 Volts 12 Volts Cat. Number Voltage Amp Hour 97014 98014 DW9106 DW9107 DW9108 DW9115 DW9116 DW9117 DW9118 DE9116 DE9118 DW911 DC011 DW0245 DE2046 DE9000 DC9310 DW9109 DC9319 DC9036 DE0240-XJ DW0242 DW0240 DC9096...

Table of Contents