ingersoll
Owner's
Manual
Installation, Operation and Maintenance
Instructions for Models SS3 and SS5
Stationary Air Compressors
IMPORTANT
INFORMATION!
READ
AND FOLLOW
THESE
INSTRUCTIONS.
RETAIN
FOR REFERENCE.
ll_*-]r-1 =1 ul li"
DEFINITIONS
/k_
WILL cause DEATH, SEVERE INJURY or substantial
property damage
WARNING
CAN cause DEATH, SEVERE INJURY or substantiaI
property damage,
CAUTION
WILL or CAN cause MINOR INJURY or property
damage.
GENERAL
SAFETY
PRECAUTIONS
,_ _
iNTAKE AIR, Can contain carbon monoxide
or other
contaminants. Will cause serious injury or death
ingersoll-Rand air compressors are not designed,
intended or approved for breathing
air Compressed
air should not be used for breathing air applications
unless treated in accordance
with all applicable
codes and regulaUons,,
WARNING
HAZARDOUS VOLTAGE Can cause serious injury
or death. Disconnect power and bteed pressure
from tank before servicing Lockout/Tagout
machine. Compressor must be connected to
properly grounded circuit See grounding
instructions
in manuat, Do not operate compressor
tn wet conditions,, Store indoors
MOVING PARTS, Can cause serious injury Do not
operate with guards removed. Machine may start
automatically
Disconnect power before servicing_
Lockout/Tagout machine,,
HOT SURFACES, Can cause serious
injury,
r
DO not
touch Allow to cool before servicing Do not touch
hot compressor or tubing
HIGH PRESSURE AIR. Bypassing_ modifying or
removing safety/relief valves can cause serious
injury or death, Do not bypass, modify or remove
safety/relief valves Do not direct air stream at body.
Rusted tanks can cause explosion and severe injury
or death Drain tank daily or after each use. Drain
valve located at bottom of tank.
z_ CAUTION
RISK OF BURSTING. Use only suitable air handling
parts acceptable for pressure of not less than the
maximum allowable working pressure of the
machine.
Your air compressor
unit is suitable for operating air too_s, caulking
guns, grease guns, sandblasters,
etc Depending on your
application,
the following accessories
may be required:
@ An air pressure regulator
to adjust the alr pressure enlering the
toot or accessory
•
An air line fitter for removal of moisiure and oil vapor in
compressed
air
•
An in-line lubricator to prolong lhe life of air tools.
ql, Separate air transformers which combine the !'unctions of air
regulation andlor moisture and dirt removal
Cenlact your nearest authorized
dealer or cal! 1-800-AIR-SERV
for
more information on air toots and accesser}as for your application
Ensure adequate lifting equipment
is available
for unloading and
moving your unit to the inslaIlatton
site
NOTE:
Lifting equipment must be property rated for the
weight of the unit.
Lift the unit by the shipping skid only,, Use straps to
prevent tipping
Lk CAUTION
Do not work on or walk under the compressor
while
it is suspended,
-...........
Be[ore signing the delivery receipl, i nspecl for damage and missing
parts
If damage or missing parts are apparenL
make the
appropriate
notation on the delivery receipt, then sign the receipt.
Immediately
contact the carrier for an inspection. All material must
be held in the receiving
location for the carrier's inspection Deiivery
receipts that have been signed without a notation of damage or
missing parts are considered
to be delivered "clear"
Subsequent
claims are then considered
to be concealed damage claims
SeUle
damage claims directly with the transportation
company
Lf you discover damage after receiving the unit (concealed
damage), the carrier must be notified within 15 days of receipt and
an inspection
must be requested
by telephone with confirmation
in
writing
On concealed
damage claims, the burden of establishing
that the unit was damaged in transit reverts back to the claimant
Read lhe unit specification
labei to verify it is the mode! ordered.
and read the meier nameplate to verify il is compatibJe with your
e_ectrical conditions
Make sure electrical
enclosures
and
componenls
are appropriate
for your applicafion
© IngersolL-Rand Company
Form SCD-B77A
Printed in U S A
March 2002
Need help?
Do you have a question about the SS3 and is the answer not in the manual?
Questions and answers
What is the proper head bolt torque for a ss3 pump?