Advertisement
See Optional, Preferred TV Connections on pages 12-13. If your cable wire is connected to your TV without a converter or descrambler box, unscrew the
wire from your TV and attach it to the ANT.IN jack on the DVD+VCR. Use the supplied round coaxial cable to connect between the DVD+VCR's RF.OUT
jack and the 75 ohm antenna input jack on the TV. With this connection, you can receive all midband, super band, and hyperband channels. With Cable Box If
a converter is required in your cable system, follow the instruction below: The cable hookup permits both TV and DVD+VCR operation. To view or record
CATV channel 1 Tune the TV to the DVD+VCR output channel (CH 3 or 4). 2 Set the DVD+VCR channel selector to the output channel of the Cable
Converter box by pressing the CH/TRK (v/V) or number (0-9) of your DVD+VCR. (Example: CH3) 3 Select the channel to view at the Cable Converter Box.
Caution Make sure the DVD+VCR is connected directly to the TV. Tune the TV to the correct video input channel. Do not connect the DVD+VCR's
DVD/VCR AUDIO OUT jack to the phono in jack (record deck) of your audio system. Do not connect your DVD+VCR via your VCR. The DVD image could
be distorted by the copy protection system. Notes With this connection, you CANNOT record one program while viewing another. If you are using a cable box
to tune channels, it is not necessary to do Auto Channel Programming as indicated on page 15. Connecting Antenna/Cable TV to DVD+VCR 1 Disconnect
the antenna leads from the rear of the TV. of your antenna. If it 2 Identify the typeThiscable from is a 75 ohm coaxialis a round cable as illustrated, it antenna
cable will connect directly to the jack marked ANT.IN on your DVD+VCR. Tip If your antenna lead wire is a flat type antenna cable, connect it to a Antenna
Adaptor (300-ohm to 75-ohm) (not supplied) and slip the Adaptor onto the ANT.IN jack. The Adaptor does not screw on to the DVD+VCR, it just slips over
Antenna Antenna Cable TV Wall Jack Flat Wire (300 ohm) Cable TV Wall Jack Back Panel of Typical Cable Box Rear of DVD+VCR 300/75 ohm Adaptor
(Not supplied) OR OR Rear of DVD+VCR 11 PREPARATION Connections (Continued) Basic TV Connections Make one of the following connections,
depending on the capabilities of your existing equipment. Optional, Preferred TV Connections Notes You can ONLY watch and listen to DVD playback
through the connections shown below. When using the COMPONENT VIDEO OUT jacks, set the video output select switch to COMPONENT. When using the
S-VIDEO OUT jack, set the video output select switch to S-VIDEO. RF coaxial connection Connect the RF.
OUT jack on the DVD+VCR to the antenna in jack on the TV using the 75-ohm Coaxial Cable supplied (R). Note If you use this connection, tune the TV to the
DVD+VCR's RF output channel (CH 3 or 4). How to set the DVD+VCR's RF output channel 1. When the DVD+VCR is turned off, press and hold CHANNEL
(v/V) on the front panel for about five seconds. It will turn itself on and "RF 03" or "RF 04" appears in the display window. S-Video connection 1 Connect the
S-VIDEO OUT jack on the DVD+VCR to the S-Video in jack on the TV using the optional S-Video cable (S). Right 2 Connect the Left and audio AUDIO OUT
jacksonofthe the DVD+VCR to the left/right in jacks TV using the supplied audio cables (A2). 2. Press CHANNEL (v/V) on the front panel or CH/TRK (v/V)
Turn off and on the DVD+VCR. Component Video (Color Stream®) connection 1 Connect the COMPONENT VIDEO OUT jacks on the DVD+VCR to the
corresponding in jacks on the TV using an optional Y Pb Pr cable (C). Audio/Video connection 1 2 Connect the DVD/VCR VIDEO OUT jack on the
DVD+VCR to the video in jack on the TV using the video cable supplied (V). Connect the Left and Right DVD/VCR AUDIO OUT jacks on the DVD+VCR to
the audio left/right in jacks on the TV (A1) using the supplied audio cables. the Right AUDIO OUT 2 Connect usingLeft and audio audio cables.
on the remote control to change the RF output channel (CH 03 or CH 04). 3.
You're reading an excerpt. Click here to read official SANYO
DVC-2600 user guide
http://somemanuals.com/dref/81636
cable.
the jack.
Advertisement
