Continuous Print - Sharp AM-900 Service Manual

AM-900U

3.2. Continuous print

This mode is used for print aging.
Select the desired pattern and input cycle, counter, pages for aging.
Printing size depends on Paper Size setting in Common Setting.
CONTINUOUS PRINT
2: ALL WHITE
[>]Key
[ENTER]Key
1: CHECK PATTERN
[>]Key
11: IDBG CHART
[>]Key
10: SG CHRAT
[>]Key
8: GENERAL CHART
9: 5% CHART
[>]Key
Select the desired pattern with the [ > ]key and [ < ]key and press the [ENTER] key.
[>]Key
CYCLE=000(m)
CYCLE=000(s)
Enter the cycle and press the [ENTER] key.
COUNT=0000(time)
Enter the counter and press the [ENTER] key.
PAGE=000(sheet)
Enter a number of pages and press the [ENTER] key.
Start aging
1. Printing pattern
1: Check Pattern : same as Figure 1
2: All White pattern : Not printed
3: All Black pattern : Printed with black within print area
4: Area pattern : Frame line is printed within print area
5: Stripe pattern : Lateral stripe (Black 2 lines and White 2 lines)
6: Halftone pattern : same as Figure 3
7: Phil chart : PHIL CHART pattern
8: General pattern
9: 5 % chart
10: SG chart
11: IDBG chart
2. Printing interval [CYCLE]: The time from printing end to next print-
ing start.
Input Range: 001 to 999 seconds or 001 to 999 minutes.
3. Repeat printing [COUNT]: The number of printing cycle.
Input Range: 0001 to 9999 times.
4. Printing pages [PAGE]: The printing pages in one cycle of printing.
Input Range: 001 to 999 pages.
3: ALL BLACK
[>]Key
[>]Key
4: AREA PATTERN
[>]Key
5: STRIP PATTERN
[>]Key
6: H-TONE PATTERN
[>]Key
7: PHIL CHART
[>]Key
2 – 12
3.3. Copy aging
This mode is used for COPY Aging. The document on the flatbed or
ADF will be scanned at the beginning of each cycle and printed it. The
meaning of "CYCLE", "COUNT" and "PAGE" are same as the case
"CONTINUOUS PRINT".
Printing size depends on Paper Size setting in Common Setting.
COPY AGING
[ENTER]Key
CYCLE=000(s)
Enter the cycle and press the [ENTER] key.
COUNT=0000(time)
Enter the counter and press the [ENTER] key.
PAGE=000(sheet)
Enter a number of pages and press the [ENTER] key.
Start aging
3.4. Life mode
This mode is used to set the life counter of the printer and the counter
of the scanner at desired values and to clear them.
LIFE MODE
[ENTER]Key
1: LIFE SETMODE
3.4.1 Life set mode
The values of life counter can be set in this mode.
1. Enter life set mode.
LIFE MODE
[ENTER]Key
1: SCAN(ADF)
[>]Key
2: SCAN(FB)
[>]Key
3: PRINT
[>]Key
4: DRUM
[>]Key
5: TONER PAGE
[>]Key
6: TONER DOTCOUNT
[>]Key
2. The cursor blinks at the top data. Four counters can be selected.
Select the desired counter and input the counter value of 10 digits
using the numeric keys. Pressing the [ENTER] key changed the
counter value.
Note: Toner page counter cannot be changed.
Caution: These counters are not cleared after memory clear mode
is executed. If it is necessary to execute the memory clear mode on
repairing the PWB, these life counters should be set again at the
same time.
[>]Key
CYCLE=000(m)
[>]Key
2: LIFE CLEAR
[ENTER]Key
0 0 0 0 0 0 0 0 0 0
[ENTER]Key
0 0 0 0 0 0 0 0 0 0
[ENTER]Key
0 0 0 0 0 0 0 0 0 0
[ENTER]Key
0 0 0 0 0 0 0 0 0 0
[ENTER]Key
0 0 0 0 0 0 0 0 0 0
[ENTER]Key
0 0 0 0 0 0 0 0 0 0
cursor position