Memory Clear - Sharp AM-900 Service Manual

b) If any key skipped, the following message will be displayed.
KEY ERROR !!
A key name that is not pressed yet is displayed so that this test can
be continued.
At that time, pressing the [STOP] key will exit this mode. And the
result will be printed.
2) Black screen
2.1.4 Check pattern mode
The effective printing area frame is printed in the specified sheet size
of the standard tray (Letter/Legal/A4).
1. Printing the pattern
Printing size depends on Paper Size setting in Common Setting.
CHECKP ATTERN
[ENTER]Key
2.1.5 Signal send mode 1
The specified signals are transmitted in the following sequence to
check the modem.
1. Press the [ENTER] key, and no signals with the loop state starts.
[ 1] No signals (making the loop)
[ 2] 4800bps (V.27ter)
[ 3] 14400bps (V.33)
[ 4] 12000bps (V.33)
[ 5] 14400bps (V.17)
[ 6] 12000bps (V.17)
[ 7] 9600bps (V.17)
[ 8] 7200bps (V.17)
[ENTER]Key
CML ON
SIGNAL SEND1
[ENTER]Key
V.17 14400bps V.33
[ENTER]Key
[ENTER]Key
V.17 12000bps V.17
[ENTER]Key
V.27ter 4800bps V.29
[ENTER]Key
[ENTER]Key
V.27ter 2400bps FLAG (300bps)
2. Pressing the [ENTER] key during transmitting CNG signal, or
pressing the [STOP] key will stop the output of signal and exit the
mode.
NOW AGING
[ 9] 9600bps (V.29)
[10] 7200bps (V.29)
[11] 4800bps (V.27ter)
[12] 2400bps (V.27ter)
[13] 300Hz (FLAG)
[14] 2100Hz (CED)
[15] 1100Hz (CNG)
[ENTER]Key
V.27ter 4800bps
[ENTER]Key
[ENTER]Key
12000bps V.33 14400bps
[ENTER]Key
V.17 7200bps
9600bps
[ENTER]Key
[ENTER]Key
7200bps V.29 9600bps
[ENTER]Key
2100 Hz (CED TONE)
[ENTER]Key
1100 Hz (CNG)
2.1.6 Signal send mode 2
The specified signals about V.34 and V.8 mode transmitted in the fol-
lowing sequence to check the modem.
1. Press the [ENTER] key, and no signals with the loop state starts.
[ 1] No signals (making the loop)
[ 2] 33600bps (V.34bis)
[ 3] 31200bps (V.34bis)
[ 4] 28800bps (V.34)
[ 5] 26400bps (V.34)
[ 6] 24000bps (V.34)
[ 7] 21600bps (V.34)
[ 8] 19200bps (V.34)
[ENTER]Key
SIGNAL SEND2
[ENTER]Key
V.34 26400bps
[ENTER]Key
[ENTER]Key
V.34 24000bps
[ENTER]Key
V.34 12000bps
[ENTER]Key
[ENTER]Key
V.34 9600bps
[ENTER]Key
ANSam
2. Pressing the [ENTER] key during transmitting ANSam signal, or
pressing the [STOP] key will stop the output of signal and exit the
mode.

2.1.7 Memory clear

Clear the backup memory including the soft switches, registration
data. After executing this mode, the memory clear report is printed.
Note: The following data is not cleared. Values for Printer life including
the adjusted value of printing void.
2.1.8 CIS adjusting mode
When the "color scan" or "monochrome scan" is selected in this mode,
the scanner motor moves from its home position to the specified value.
Then, the document reading lamp is turned on.
CIS ADJUST
[ENTER]Key
The motor will move to the specified position and the reading lamp is lit on.
1. Press the [STOP] key to exit the mode.
2 – 9
AM-900U
[ 9] 16800bps (V.34)
[10] 14400bps (V.34)
[11] 12000bps (V.34)
[12] 9600bps (V.34)
[13] 7200bps (V.34)
[14] 4800bps (V.34)
[15] 2400bps (V.34)
[16] 0-300bps (V. 21)
[17] ANSam
[ENTER]Key
CML ON V.34
[ENTER]Key
[ENTER]Key
V.34 28800bps V.34
[ENTER]Key
V.34
V.34 21600bps
[ENTER]Key
[ENTER]Key
V.34 14400bps V.34
[ENTER]Key
V.34
V.34 7200bps
[ENTER]Key
[ENTER]Key
V.21 0 - 300bps V.34
1: COLOR
2: MONO
33600bps
31200bps
19200bps
16800bps
4800bps
2400bps
1 key
2 key