Table of Contents
Advertisement
TROUBLESHOOTING
Most treadmill problems can be solved by follow-
ing the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assis-
tance is needed, see the front cover of this manual.
SYMPTOM: The power does not turn on
a. Make sure that the power cord is plugged into a
surge suppressor and that the surge suppressor
is plugged into a properly grounded outlet (see
page 9). Use only a surge suppressor that meets
all of the specifications described on page 9.
IMPORTANT: The treadmill is not compatible
with GFCI-equipped outlets and may not be
compatible with AFCI-equipped outlets.
b. After the power cord has been plugged in, make
sure that the key is inserted into the console.
c. Check the power switch located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the switch has tripped. To reset the
power switch, wait for five minutes and then press
the switch back in.
c
Tripped
SYMPTOM: The power turns off during use
a. Check the power switch (see the drawing above).
If the switch has tripped, wait for five minutes and
then press the switch back in.
b. Make sure that the power cord is plugged in. If the
power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
c. Remove the key from the console, and then
reinsert it.
Reset
16
d. If the treadmill still will not run, please see the front
cover of this manual.
SYMPTOM: The console displays remain lit when
you remove the key from the console
a. The console features a display demo mode,
designed to be used if the treadmill is displayed in
a store. If the displays remain lit when you remove
the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a
few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 14 to turn off the
demo mode.
SYMPTOM: The displays of the console do not
function properly
a. Remove the key from the console and UNPLUG
THE POWER CORD. Place the treadmill in
the storage position (see HOW TO FOLD THE
TREADMILL on page 15).
Remove the six indicated M4.2 x 13mm Washer
Head Screws (5) and the six Foot Rail Flat
Washers (25). Next, lower the Frame (50) (see
HOW TO LOWER THE TREADMILL FOR USE on
page 15).
5
25
5
50
5
25
5
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Cadence G 5.9 Treadmill and is the answer not in the manual?
Questions and answers
How and where do I lubricate the power.
How do I lubricate the motor?
My Weslo Cadence 5.9I squeaks for about a minute after starting. I don't see any instructions on lubrication in the manual other than the belt.
Your Weslo Cadence G 5.9 treadmill features a walking belt that is pre-coated with high-performance lubricant. Do not apply silicone spray or other substances to the walking belt or walking platform unless instructed by an authorized service representative. If the treadmill is squeaking, check for proper belt alignment and tension. If necessary, adjust the walking belt or inspect other components for wear.
This answer is automatically generated
How do I lubricate the belt, I **** very handy.
To lubricate the belt on a Weslo Cadence G 5.9 Treadmill, apply the recommended World Famous Treadmill Lube to the underside of the walking belt once per year. Do not use silicone spray or other substances unless instructed by an authorized service representative.
This answer is automatically generated
The display on the console is very light and almost impossible to read. Is there some sort of backlight switch that I can turn on to better illuminate the info on the display (distance walked etc.)? Thanks
Lubrication required?
Yes, the Weslo Cadence G 5.9 Treadmill requires lubrication. A product listing mentions a "Weslo Cadence G 5.9 Treadmill Walking Belt + Free 1oz Lube," indicating that lubrication is needed for maintenance.
This answer is automatically generated
When the treadmill is plugged in and turned on the display shows "FF". No other controls work. Do you know how to fix this?