Copy; Copy Data To Copy 1 Drive/Set Copy 1 Drive; Copy Data To Copy 2 Drive/Set Copy 2 Drive - Mitsubishi Electric DX-TL5000E Installer Manual

Copy

This item is used to copy data from the main device to a
copy device.

Copy Data to Copy 1 Drive/Set Copy 1 Drive

This item is used to copy data to Copy 1 device by specify-
ing the start and end points. The points are specified by
the date and time or the book mark. This function is useful
for copying the data of the short period of time.
• Before executing the copy, make sure that the Copy
1 device is connected and set in the <Add/Remove
HDD Device> and <Add/Remove DVD/CD Drive>
(System Menu Memory) correctly.
User Menu
2 Copy
1 Copy Data to Copy 1 Drive
1 + 2 Range of Copy
Set Copy 1 Drive
3
1. Set the camera number to be copied.
step
• The button function changes between "All Off"
and "All On" each time you select this button. You
can switch on and off for all the cameras easily
by using this button.
• The picture is not copied when there is no
recorded picture of the set camera number or
time.
2. Select "Other settings" and then set the detailed
step
settings.
From Device: Sets the device which contains the
data to be copied. The available setting items are
"Main" and "Copy 2."
From Group: Sets the group which contains the
data to be copied. The available setting items are
"Normal," "Alarm," and "LPA" for main, "SerialBus,"
"NAS," "SCSI," "DVD/CD," and "Internal" for copy
2.
To Copy 1: Sets the group name to where the data
is copied. The available setting items are
"SerialBus," "NAS," "SCSI," "DVD/CD," and
"USBmemory."
Copy Data: Sets the data area to be copied. The
available setting items are "Alarm" and "All."
Overwrite: Selects whether or not to overwrite the
existed data.
Auto Eject: Selects whether to eject media (CD/
DVD) automatically when the copy is over.
• "Alarm" appears for "From Group" when "Alarm
Recording Area" (System Menu Memory Data
Management Setting for Main Memory Change
Partition Setting) is set to other than "0 %."
• "LPA" appears for "From Group" when "Long Pre-
Alarm Area" (System Menu Memory Data
Management Setting for Main Memory Change
Partition Setting) is set to other than "0 %."
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
44
• When copying the data to DVD and setting "Overwrite"
to "On," the unit clears the existing data on the disk
before overwriting with new data. Note that clearing
the data takes about 30 to 40 minutes. You cannot
cancel operation during clearing the data of the DVD.
• When copying the data while "Copy Data" is set to
"Alarm," the unit performs copy operation, however,
the data is not recorded if there is no alarm recording
data within the specified range of copy. In case of
CD/DVD disc, the remaining capacity becomes low
because only the management information is
recorded. It is recommended to carry out "Calculate"
in <Copy Data to Copy 1 Drive> to confirm whether
or not there is alarm recording data in the specified
range.
3. Set the start, start/end, or end point of copy by
step
specifying the date and time or the book mark
number.
4, 5
steps
Start: Sets only the start point of copy. The data is
copied from the specified start point as much data
as possible with the remaining capacity of the media
3
step
to be copied.
Start/End: Sets the start and end points of copy.
End: Sets only the end point of copy. The data is
1, 2
steps
copied as much data as possible with the remaining
capacity of the media to be copied until the specified
end point reaches.
• To set the book mark point, select "Bookmark"
and then select the desired book mark number.
• To copy from the oldest recording time, select
"Copy Start Time." To copy to the latest recording
time, select "Copy End Time."
4. Select "Calculate" to calculate the capacity of data
step
to be copied.
• When using "End," the copy cannot be executed
unless the calculation of the capacity of data to be
copied is completed.
• When using "Start" or "Start/End" and executing copy
without calculating the capacity of data to be copied,
the progress or the time of the copy may not be
displayed correctly because the unit cannot specify
the capacity of data to be copied.
5. Select "Execute."
step
• The copy starts.
• To stop copy manually, select "Cancel" in the
progress screen. The data which has been copied
before cancelling is copied.

Copy Data to Copy 2 Drive/Set Copy 2 Drive

This item is used to copy the data to Copy 2 device by
specifying only the start point. The point is specified by the
date and time or the book mark. The copy continues until
the end point of the recording data reaches or the media to
be copied becomes full unless the copy is stopped manu-
ally (when "FIFO Overwrite" is set to "Off"). This function is
useful for making backup of the recording data.
• Before executing the copy, make sure that the Copy
2 device is connected and set in the <Add/Remove
HDD Device> and <Add/Remove DVD/CD Drive>
(System Menu Memory) correctly.
User Menu