Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Precor S3.25
Summary of Contents for Precor S3.25
- Page 1 S3.25 Leg Press Option Assembly Instructions...
-
Page 2: Important Safety Instructions
For information about product operation or cables are secure and in good working Il est conseillé de subir un examen médical complet service, check out the Precor web site at condition. avant d’entreprendre tout programme d’exercise. Si www.precor.com or contact an authorized •... -
Page 3: Table Of Contents
Installation Requirements ....................Assembly Tips ....................... Assembly Instructions ................6 1. Remove the Shroud ....................2. Attach the Cross Brace to the S3.25 ................3. Assemble the Frame ....................4. Assemble the Seat Pads .................... 11 5. Route the Cable ......................12 6. -
Page 4: Before You Begin
S3.25 Leg Press Option Assembly Instructions Before You Begin Thank you for purchasing the Leg Press Option for your Precor equipment. This option will add a new dimension to your strength-training regimen. For proper installation, please read this guide thoroughly and follow the assembly instructions. -
Page 5: Preparations
S3.25 Leg Press Option Assembly Instructions Installation Requirements Assembly Tips • A 6-inch scale is provided at the bottom of every Follow these installation requirements when assembly instruction page. Use this scale to identify assembling the unit: the correct size bolts and spacers. The head of a •... -
Page 6: Assembly Instructions
5 before proceeding. The Leg Press Option comes in one box. It can be installed on either the S3.25 or S3.45 Precor Strength Training Equipment. Note that the location where you attach the Cross Brace to the Seat Frame differs. -
Page 7: Remove The Shroud
Top Beam fastener six 2¾-inch bolts six washers six locknuts B. Pull the Shroud away from the S3.25 and lay it and 6 - 2¾" bolts its fasteners on the floor in a secure place. 6 - washers 6 - locknuts Note: The top of the Shroud has a notch in it to help you clear the Top Beam fastener. -
Page 8: Attach The Cross Brace To The S3.25
2. Attach the Cross Brace to the S3.25 Note: If you are assembling the Leg Press Option along with the S3.25, you should complete Step 10 in the S3.25 Assembly and Maintenance Guide before attaching the Cross Brace. A. Align the Cross Brace to the S3.25 Rear Upright... -
Page 9: Assemble The Frame
Cross the Seat Frame stable and upright while you Brace to the S3.25 Leg Press Option. attach the Cross Brace C. Slide the Backpad Support into the Seat Frame, locking it in place with the Pop Pin. - Page 10 S3.25 Leg Press Option Assembly Instructions D. Assemble the Footrest by resting the Pivot Arm on the Rubber Bumper. Make sure that the red 2 - large ½" x 3¼" bolts arrow on the back of the Footrest points toward 4 - ½"...
-
Page 11: Assemble The Seat Pads
Note: Make sure that the seams on the Seat Pads face down toward the frame. Note: If you are assembling the Leg Press Option and the S3.25 simultaneously, return to Step 11 in the S3.25 Assembly and Maintenance Guide now. Seat Frame Seat Pad 2 - 3"... -
Page 12: Route The Cable
S3.25 Leg Press Option Assembly Instructions 5. Route the Cable Push the Pivot As you route the Cable through the pulleys on the Leg Arm forward Pivot Arm Press Option, wrench tighten the fasteners on each pulley as you go. Make sure that the Cable slides freely along the pulley (and beneath the cable retainer). -
Page 13: Assemble The Cable And Pulleys
S3.25 Leg Press Option Assembly Instructions 6. Assemble the Cable and Pulleys Rear Upright You can identify Cables by the white numbers placed at the end of the Cable. A. Place Leg Press Option Cable 40538-101 between a Attach this cable retainer and one 3½-inch pulley. - Page 14 Cable Tree using the 1¼-inch buttonhead bolt and thin nylock nut removed in Step 6E. Wrench tighten. Note: If you are assembling the Leg Press Option and the S3.25 simultaneously, go to Step 21 in the S3.25 Cable Tree Assembly and Maintenance Guide now.
-
Page 15: Replace The Shroud
S3.25 Leg Press Option Assembly Instructions 7. Replace the Shroud A. Pick up the Shroud and fasteners from the location Top Beam where you left them in Step 4B. B. Replace the Shroud by realigning the mounting holes and inserting six 2¾-inch bolts... -
Page 16: Adjustments
S3.25 Leg Press Option Assembly Instructions Top Cap Weight Adjustments After the Leg Press Option is assembled, you should check the Cables for proper tension. These are some Top Weight obvious signs that cable problems exist: ✔ Excess slack exists in the Cable. -
Page 17: Rotate The Cam Washer
S3.25 Leg Press Option Assembly Instructions Weight then further adjustments are needed. Continue with steps 2 and 3. 2. Rotate the Cam Washer If the Top Cap Weight does not rest on the Top Weight, you must make further adjustments. -
Page 18: Adjust The Rubber Bumper On The Leg Press Option
With the slack removed from the Cables, you are now Rubber Bumper ready to use the Leg Press Option. Thank you for choosing Precor Strength-Training Equipment. Note: For maintenance instructions, refer to your S3.25 Assembly and Maintenance Guide. Weight Pin Locknut Bracket Step 3. - Page 19 2. Bearings, Guide rods, Cams, Pulleys, Belts, Cables, Hand grips, and Miscellaneous parts will be Servicers for warranty trips within their normal warranted for a period of three years. Note that for the Precor Strength Products S3.xx, and service area to repair motorized treadmills and the Pacific Fitness Solana and Zuma, the warranted period is five years.
-
Page 20: Warranty Card
Exploded Views # 44661-101 of Precor’s product designs is hereby forewarned that Precor considers the unauthorized appropriation of its proprietary rights to be a very serious matter. Precor will vigorously Warranty Card # 36287-108 pursue all unauthorized appropriation of its proprietary rights.
Need help?
Do you have a question about the S3.25 and is the answer not in the manual?
Questions and answers