Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Precor move beyond S3.25
Summary of Contents for Precor move beyond S3.25
- Page 1 S3.25 Strength-Training Fitness Equipment Assembly and Maintenance Guide...
-
Page 2: Important Safety Instructions
• Assemble and operate the S3.25 on a solid, level manufacturer: such attachments might cause surface. Locate the unit a few feet from walls or Serial number: _____________ injuries. -
Page 3: Table Of Contents
S3.25 Assembly and Maintenance Guide Table of Contents Important Safety Instructions ............... 2 Personal Safety During Assembly .................... 2 Obtaining Service ........................2 Before You Begin ................... 5 Unpacking the Equipment ......................5 Optional Equipment ........................5 Preparations for Assembly ................6 Required Tools .......................... - Page 4 S3.25 Assembly and Maintenance Guide Open Box 4 ..........................22 11. Assemble Weight Stack ....................23 12. Feed Upper Cable ......................24 13. Attach Lat Bar Holders ....................25 14. Feed Cable From Cable Tree ..................26 15. Attach Leg Curl Cables to Lower Pulley Bracket ............29 16.
-
Page 5: Before You Begin
S3.25 Assembly and Maintenance Guide Before You Begin Thank you for purchasing the S3.25. This unit is part of the Pacific Fitness line of quality strength training machines, which let you target specific muscle groups to achieve better muscle tone and overall body conditioning. -
Page 6: Preparations For Assembly
Note: A few of the bolts used to assemble the Preparations this guide. S3.25 are longer than 6 inches. You may want to • Set up the S3.25 on a solid, flat surface. A use a measuring tape to accurately identify the... -
Page 7: Assembly Instructions
S3.25 by yourself. Review the Installation Requirements on page 6 before proceeding with the following steps. The S3.25 comes in four boxes. (See the diagram at the right.) Be careful to open boxes and assemble components in the sequence presented in this guide. -
Page 8: Open Box 1
S3.25 Assembly and Maintenance Guide Open Box 1 Use tie cutters to open the box. The illustration shows how the S3.25 will look after you complete this section. Note: Some items in these boxes may not be needed until later in the assembly process. -
Page 9: Attach Rear Upright To Main Upright
S3.25 Assembly and Maintenance Guide 1. Attach Rear Upright to 1 - 4" bolt Main Upright 2 - washers 1 - locknut Begin the assembly by placing the Rear Upright and 1 - 3" bolt Top Beam Main Upright on the floor. -
Page 10: Attach Chest Press Base
S3.25 Assembly and Maintenance Guide 2. Attach Chest Press Base A. Attach the Chest Press Base to the Main Upright using one 3¼-inch bolt two washers one locknut Finger tighten. B. Attach the Floor Base to the Chest Press Base... -
Page 11: Open Box 2
S3.25 Assembly and Maintenance Guide Open Box 2 Use tie cutters to open the box. The illustration shows how the S3.25 will look after you complete this section. Note: Some items in these boxes may not be needed until later in the assembly process. -
Page 12: Assemble Leg Curl Seat Extension
S3.25 Assembly and Maintenance Guide 3. Assemble Leg Curl Seat Extension Leg Curl Seat Upright A. Use a flathead screwdriver to remove the black end cap on the Leg Curl Seat Upright. B. Detach the bolts at the bottom of the Upright Flats. -
Page 13: Attach Rotating Arm And Handles
S3.25 Assembly and Maintenance Guide 4. Attach Rotating Arm and Handles A. Attach the Rotating Arm to the Upright Flats using 2 - ¾" buttonhead bolts two ¾-inch buttonhead bolts Tighten with 6-mm Allen wrench. B. Attach the Handles to the Seat Upright using two 3¼-inch bolts... -
Page 14: Attach Roller Pads
S3.25 Assembly and Maintenance Guide 5. Attach Roller Pads A. Insert the Leg Curl Roller Pad Rod. B. Slide the Leg Curl Roller Pads on the Rod. Center the Pads on the Rod. Insert End Caps into the end Leg Curl of the Rod. -
Page 15: Assemble Leg Curl Seat
S3.25 Assembly and Maintenance Guide 6. Assemble Leg Curl Seat A. Attach the Backpad Support Tubes to the Seat Seat Pad Backpad Support Upright using Tubes one 5½-inch bolt two ½-inch washers one ½-inch locknut Note: The tube with the Selector Pivot Flat is nearest the Weight Stack. - Page 16 S3.25 Assembly and Maintenance Guide D. Attach the lower section of the Backpad to the lower hole of the right Backpad Support Tube using two 3-inch bolt Backpad Support Tubes two washers Headrest Finger tighten. E. Attach the Leg Curl Handle to the holes at the top of 2 - 1¼"...
-
Page 17: Open Box 3
S3.25 Assembly and Maintenance Guide Open Box 3 Use tie cutters to open the box. The diagram shows how the S3.25 will look after you complete this section. Note: Some items in these boxes may not be needed until later in the assembly process. -
Page 18: Assemble Chest Press Seat
S3.25 Assembly and Maintenance Guide 7. Assemble Chest Press Seat A. Attach the Chest Press Upright to the Chest Press Seat using four ¾-inch bolts four washers Finger tighten. B. Attach the middle hole at top of the Chest Press Upright to the Main Upright using one 3½-inch bolt... -
Page 19: Attach Press Arm Assembly
S3.25 Assembly and Maintenance Guide 8. Attach Press Arm Assembly CAUTION: This step requires two people. Do not pinch yourself between the Press Arm and the 2 - 4" bolts Prestretch Tube. 4 - washers 2 - locknuts A. Attach the Press Arm Assembly to the Main... -
Page 20: Attach Handlebars
S3.25 Assembly and Maintenance Guide 9. Attach Handlebars A. Slide each Handlebar (one at a time) on the Pivot Shaft. B. To the end of each threaded Pivot Shaft, attach Press Arm one ½-inch washer Assembly one ½-inch hat washer one ½-inch locknut... -
Page 21: Assemble Chest Press Seat
2 - 1¼" bolts Wrench tighten. 2 - washers Note: If you have purchased the Leg Press Option, open the S3.25 Leg Press Option box now and begin Seat Stem Chest Press with Step 2. Upright 1 - ½" x 5¼" bolt... -
Page 22: Open Box 4
S3.25 Assembly and Maintenance Guide Open Box 4 Use tie cutters to open the box. The diagram shows how the S3.25 will look after you complete this section. Note: Set aside the 2¾-inch bolt that is wrapped with blue tape. It has special threads than can only be used in step 16E. -
Page 23: 11. Assemble Weight Stack
S3.25 Assembly and Maintenance Guide 11. Assemble Weight Stack 2 - 4" bolts Guide Rod Bracket Important: Position your unit in its permanent location Guide Rod 4 - washers before assembling the Weight Stack. Bracket 2 - locknuts A. Place a Weight Cushion on the base of two Guide Guide Rods Rods (found in Box 1). -
Page 24: Feed Upper Cable
S3.25 Assembly and Maintenance Guide 12. Feed Upper Cable 1 - 4½" pulley 1 - 2½" bolt A. Attach a 4½-inch pulley to the top of the Main 2 - washers Upright using 1 - barrel spacer one 4¼-inch bolt... - Page 25 S3.25 Assembly and Maintenance Guide G. Insert the Selector Stem in the Weight Stack with the threaded hole at the top. Hold the Selector Stem with several holes above the Cap Plate. Insert the Weight Pin to suspend the Selector Cable 44370-103 Stem.
-
Page 26: Attach Lat Bar Holders
S3.25 Assembly and Maintenance Guide 13. Attach Lat Bar Holders A. Attach the Lat Bar Holders to the Top Beam using two 3¼-inch bolts 2 - 3¼" bolts four washers 4 - washers Top Beam two locknuts 2 - locknuts B. -
Page 27: Feed Cable From Cable Tree
S3.25 Assembly and Maintenance Guide 14. Feed Cable From Cable Tree Main Upright A. Feed the Spring Clip end of Cable 44371-103 under Upper Pulley 1 - 4½" pulley a 4½-inch pulley, through the lower pulley window of Window 1 - 2¾" bolt... - Page 28 S3.25 Assembly and Maintenance Guide E. In the middle hole on the Press Arm Flats, make a retainer pin using 1 - 3½" pulley one 2-inch bolt 1 - 2" bolt 1 - 2" bolt two washers 2 - washers...
-
Page 29: Attach Leg Curl Cables To Lower Pulley Bracket
S3.25 Assembly and Maintenance Guide 15. Attach Leg Curl Cables to Lower Pulley Bracket Cable 44375-103 goes to the Cable Tree A. Wrap Cable 44376-102 around a 3½-inch pulley so that the U end of the Cable faces up toward the Cable Tree. -
Page 30: Attach Leg Curl Cables To Seat Upright
S3.25 Assembly and Maintenance Guide 16. Attach Leg Curl Cables to Seat Upright 1 - 2¾" bolt (wrapped with blue tape) 1 - washer A. Attach the Pulley Cover to the Main Upright Base using 1 - 2¾" bolt (without blue tape) -
Page 31: Feed Top Cable 44376-102
S3.25 Assembly and Maintenance Guide 17. Feed Top Cable 44376-102 A. Attach Cable 44376-102 to the Rotating Arm using one 2¾-inch bolt two step spacers one locknut B. Wrap the Cable around a 4½-inch pulley and attach it and a cable retainer to the Upright Flats using one 4½-inch bolt... -
Page 32: Feed Bottom Cable 44375-103
S3.25 Assembly and Maintenance Guide 18. Feed Bottom Cable 44375-103 A. Feed Cable 44375-103 through the Upright Flats, through the Seat Upright Window, and into the Pulley Window at the end of the Seat Upright. 1 - 3½" pulley 1 - 2¾" bolt B. -
Page 33: Attach Surgical Tubing To Top Beam
S3.25 Assembly and Maintenance Guide 19. Attach Surgical Tubing to Top Beam 1 - 3¼" bolt A. Attach the other end of the surgical tubing to the 2 - washers 1 - ½" barrel spacer Top Beam using 1 - locknut Top Beam one 3¼-inch bolt... -
Page 34: Attach Leg Curl Cables To Cable Tree
Cable in the opposite corner of the Cable Tree. Reattach the U end of the Cable with surgical tubing. Note: If you are assembling the Leg Press Option simultaneously, go to Step 5 in the S3.25 Leg Press Option Assembly Instructions now. Cable 44376-102 Cable 44375-103 Step 20. -
Page 35: Attach Accessories
S3.25 Assembly and Maintenance Guide 21. Attach Accessories A. Attach the Lat Bar to the Spring Clip at the end of the Top Beam. B. Attach the Ab Crunch Strap to the Spring Clip on the Press Arm. C. Attach the Ankle Strap to the Spring Clip on the Lat Bar Leg Station. -
Page 36: Attach Shrouds
C. Attach the Small Shroud to the Angle Bracket in the Main Upright Base using one ¾-inch bolt one washer 6 - 2¾" bolts This completes the assembly of your Precor S3.25. 12 - washers 6 - locknuts Small Shroud Small Shroud 1 - ¾"... -
Page 37: Adjustments And Maintenance
Adjustments and Maintenance Top Cap Weight After the S3.25 is completely assembled, you must check the Cables for proper tension. Obvious signs that Cable problems exist include: Top Weight ✔ The Cap Plate does not rest squarely on the top weight of the Weight Stack. -
Page 38: Selector Stem Adjustments
U Bracket A. Remove the Weight Pin from the Weight Stack. B. Perform an exercise using each part of the S3.25. When the base of the Selector Stem is clear of the Weight Stack, observe the position of the 1 ½"... -
Page 39: Backward Angle Adjustment
S3.25 Assembly and Maintenance Guide D. Reassemble the Cap Plate, Selector Stem, and Cable Clamp. E. Test the movement of the Selector Stem inside the Backward Angle Adjustment Weight Stack. If the Selector Stem continues to contact the plates, repeat steps A through E until the Selector... -
Page 40: Side-To-Side Vertical Adjustment
S3.25 Assembly and Maintenance Guide Side-to-Side Vertical Adjustment If the Selector Stem contacts the inside of the Weight Pull the Selector Stem and Stack during use or the Weight Pin becomes difficult to Top Cap Weight up to insert in the Weight Stack, the Selector Stem may be expose at least 5 holes. - Page 41 page 41...
- Page 42 page 42 Please detach and mail in the warranty registration within ten days of purchase.
-
Page 43: Precor Residential Equipment Limited Warranty
Satisfactory proof of purchase is required in all cases. For any product described above that fails to conform to its warranty, Precor will provide, at their option, one of the following: (1) repair; (2) replacement; or (3) refund of the purchase price. Precor Limited Warranty service Conditions and Restrictions may be obtained by contacting the authorized dealer from whom you purchased the item. -
Page 44: Warranty Registration
Precor is widely recognized for its innovative, award winning designs of exercise equipment. Precor aggressively seeks U.S. and foreign patents for Warranty Registration # 45623-102 both the mechanical construction and the visual aspects of its product design. Any party contemplating the use of Precor’s product designs is hereby Warranty Card # 36287-110 forewarned that Precor considers the unauthorized appropriation of its proprietary rights to be a very serious matter.
Need help?
Do you have a question about the move beyond S3.25 and is the answer not in the manual?
Questions and answers