Table of Contents
Advertisement
Warning Display
No Camera Signal
Camera signal is lost or distorted.
Please check the camera and cable
connection.
It can use as it is though a slight error
occurred.
System suspended due to unstable
processing. Recording will be resumed.
HDD
was disconnected.
System suspended due to unstable processing.
Start operation again.
The alteration part is found in the data.
Recorder detected technical problems
on the device.
The recorder has been rebooted. The problem
is not critical, but check the recorder.
Internal temperature is getting too high,
check the ventilation of the recorder.
Internal temperature is getting too high,
stop the operation of the recorder
immediately.
The fan of the recorder needs to be checked.
Copying data stopped because of new record
overwrites the old data.
New record will soon overwrite the old data
in copying.
Stop the recording, if you want to continue the
copying.
(none)
#8 :
14
: Recording 24
34
: Copy 1
(The following numbers are in
00 : A (Internal)
03 : D (Internal)
30 to 35 : SCSI (External)
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Warnings and CALL OUT output
: Playback
44
: Restore
74
: Copy 2
)
01 : B (Internal)
02 : C (Internal)
10 to 26 : USB (External)
40 to 47 : NAS (External)
Countermeasure
• Check whether the unit
and camera are properly
connected, and that electri
-city is on.
• Check whether the video
signal is being properly
outputted.
• Check to see if there is a
camera set for operation
with no video signal input.
• Continue the operation
when there is no abnormality.
• When the error occurs
continuously, check the
HDD/media, cable and
termination and restart the unit.
• Restart the unit.
• Check the unit.
• Turn off the power and
change the installation
condition.
• Turn off the power and
change the installation
condition.
• Turn off the power and
stop using.
• Stop HDD recording to
continue copy/archive.
• Stop HDD recording to
continue copy/archive.
• Stop copy/archive to
continue HDD recording.
• Restarts by watchdog
operation.
Regarding LOG1400: Displays during recording. The system shuts down once and then
resumes recording. (The error HDD is automatically deleted from the registration for the
recording device. The recording is continued until all the registered HDDs are used up.)
Regarding LOG24 to 74: Displays during copying or playback. The playback or copy
stops because the system shuts down. Carry out playback or copy again.
CALL OUT
Cancelling
Log number
output
the warning
Stop recording.
Fixed
LOG54
#7
Output video
signals.
Click "Clear
Warning" or
press the E
button.
None
LOG13
#8
LOG23
#8
LOG33
#8
LOG43
#8
LOG73
#8
Fixed
Click "Clear
LOG14
#8
Warning" or
press the E
button.
LOG24
#8
None
LOG34
#8
LOG44
#8
LOG74
#8
None
Click "Clear
LOG55
#7
Warning" or
press the E
button.
Fixed
Click "Clear
LOG6200
Warning" or
press the E
button.
Fixed
Click "Clear
LOG5100
Warning" or
press the E
button.
Fixed
Click "Clear
LOG5200
Warning" or
press the E
button.
Fixed
Click "Clear
LOG5201
Warning" or
press the E
button.
Lower the
temperature.
Click "Clear
LOG5300
Fixed
Warning" or
press the E
button.
Rotate the fan.
None
Click "Clear
LOG3500#3
Warning" or
LOG7500#4
press the E
button.
None
Click "Clear
LOG3600#3
Warning or
LOG7600#4
press the E
button.
–
LOG5101
#1
35
Advertisement
Table of Contents
