Analog Input Spec; Analog Output Specs - Yamaha 01V96i Owner's Manual

Analog Input Spec

Input PAD GAIN
–60 dB
0
INPUT A/B
1–12
–16 dB
20
–26 dB
INPUT 13–16
—
+4 dB
CH INSERT IN
—
1–12
2TR IN [L, R]
—
1. Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V) or the nominal output level when the unit
is set to maximum gain. (All faders and level controls are maximum position.)
2. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD).
3. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND).
4. CH INSERT IN/OUT phone jacks are unbalanced. (Tip=OUTPUT, Ring=INPUT, Sleeve=GND).
In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms.
For 2TR IN levels, 0 dBV is referenced to 1.00 Vrms.
All input AD converters (CH INPUT 1–16) are 24-bit linear, 128-times oversampling. (@fs=44.1, 48 kHz)
+48 V DC (phantom power) is supplied to CH INPUT (1–12) XLR type connectors.
Three PHANTOM +48V switches CH1–4, 5–8, 9–12 turn on the phantom power for inputs 1–4, 5–8, 9–12 respectively.

Analog Output Specs

Actual Source
Output
Impedance
75 Ω
STEREO OUT [L, R]
150 Ω
OMNI OUT 1–4
150 Ω
MONITOR OUT [L, R]
600 Ω
CH INSERT OUT 1–12
600 Ω
2TR OUT [L, R]
100 Ω
PHONES
1. XLR-3-32 type connectors are balanced (1=GND, 2=HOT, 3=COLD).
2. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND).
3. CH INSERT IN/OUT phone jacks are unbalanced. (Tip=OUTPUT, Ring=INPUT, Sleeve=GND).
4. PHONES stereo phone jack is unbalanced (Tip=LEFT, Ring=RIGHT, Sleeve=GND).
In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms.
2TR OUT [L, R] levels, 0 dBV is referenced to 1.00 Vrms.
All output DA converters are 24-bit, 128-times oversampling. (@fs=44.1, 48 kHz)
Actual Load For Use With
Impedance Nominal
Sensitivity
(0.245 mV)
50–600 Ω
Mics & 600 Ω
3 kΩ
Lines
600 Ω Lines
10 kΩ
600 Ω Lines
10 kΩ
600 Ω Lines
10 kΩ
Output level
For Use With
Nominal
Nominal
+4 dB
600 Ω Lines
(1.23 V)
+4 dB
10 kΩ Lines
(1.23 V)
+4 dB
10 kΩ Lines
(1.23 V)
–2 dB
10 kΩ Lines
(616 mV)
–10 dBV
10 kΩ Lines
(316 mV)
8 Ω Phones
4 mW
40 Ω Phones
12 mW
Analog Input Spec
Input level
Max.
1
Nominal
before clip
–70 dB –60 dB –40 dB
(0.775 mV) (7.75 mV)
–26 dB –16 dB +4 dB
(38.8 mV) (123 mV) (1.23 V)
–6 dB +4 dB +24 dB
(388 mV) (1.23 V) (12.28 V)
–36 dB –26 dB –6 dB
(12.3 mV) (38.8 mV) (388 mV)
–6 dB +4 dB +24 dB
(388 mV) (1.23 V) (12.28 V)
–12 dB –2 dB +18 dB
(195 mV) (616 mV) (6.16 V)
–10 dBV –10 dBV +10 dBV
(316 mV) (316 mV) (3.16 V)
Max.
before clip
+24 dB
XLR-3-32 type (Balanced)
(12.28 V)
+24 dB
Phone jack (TRS) (Balanced)
(12.28 V)
+24 dB
Phone jack (TRS) (Balanced)
(12.28 V)
+18 dB
Phone jack (TRS) (Unbalanced)
(6.16 V)
+10 dBV
RCA Pin Jack (Unbalanced)
(3.16 V)
25 mW
Stereo Phone Jack (TRS) (Unbalanced)
75 mW
61
Connector
A: XLR-3-31 type
2
(Balanced)
B: Phone jack
3
(TRS) (Balanced)
Phone jack (TRS)
3
(Balanced)
Phone jack (TRS)
4
(Unbalanced)
RCA pin jack
(Unbalanced)
Connector
1
2
2
3
4
01V96i—Owner's Manual