Troubleshooting - Yamaha 01X Software Installation Manual

Yamaha 01x synthesizer: installation guide

Hide thumbs Also See for 01X:

Owner's manual (156 pages)

Service manual (153 pages)

Supplementary manual (21 pages)

Table Of Contents

Table of Contents

Available languages

Cannot install the driver.

• Is the mLAN cable properly connected? Check the connection; disconnect the mLAN cable once, then insert it again.

The mLAN connection does not work.

• Has the driver been installed?...................................................................................................................................................................pages 3, 17

• Is the mLAN cable properly connected? Check the connection; disconnect the mLAN cable once, then insert it again.

• (For Windows) Is mLAN set to "ON"? From the taskbar, right click on the mLAN Manager icon.......................................................... page 10

• (For Windows) When adding a new IEEE 1394 card, right click on the mLAN Manager icon in the taskbar and select "ON."............... page 10

• Is the ACTIVE lamp on the rear panel of the 01X lit (in blue)? If it is not lit, check the followings:

• In mLAN Driver Setup (from taskbar, right click on the mLAN Manager icon, then "Driver Setup"), is the Status indicator blue?

If not, restart the 01X and re-enable connection by using mLAN Auto Connector. ..................................................................................... page 10

• Is mLAN AUTO W.CLK (Auto Wordclock) on the 01X set to "ENABLE"? ........................................................................................pages 9, 20

• Has connection been enabled with mLAN Auto Connector? Re-enable connection if necessary.

.........................................................................................................................................."Settings by mLAN Auto Connector" on pages 9 and 20

• Have you changed the device? Even if the model is the same, if the actual device is different,

it is necessary to re-enable connection by using mLAN Auto Connector.

.........................................................................................................................................."Settings by mLAN Auto Connector" on pages 9 and 20

• Is there a loop connection? Check the cabling and make sure none of the devices are connected in a loop.

Example of loop connection

• There may be a limit on the IEEE 1394 interface of your computer as to the number of ports that can be used simultaneously.

Check how many ports can be used simultaneously.

• Turn off all devices on the mLAN network (except the computer) and re-connect each device one-by-one until the device caus-

ing the problem is found.

• (For Windows) (When removing the mLAN bus from the [Safely Remove Hardware] setting of the task bar.) Restart the com-

puter when using mLAN again.

• With Macintosh notebook computers such as the iBook and PowerBook, always first connect the 01X and mLAN cable then

turn on the power of the 01X, before starting up the computer.

The mLAN Driver (MIDI/Audio) is not detected from the application (DAW, audio sequencer, etc.).

• (For Windows) Is mLAN (mLAN Driver) set to "ON"? From the taskbar, right click on the mLAN Manager (mLAN icon). ............... page 10

• Is the 01X properly connected to the computer by an mLAN cable, and is the power turned on?

(Try starting the mLAN Auto Connector and "connect" again.)

.........................................................................................................................................."Settings by mLAN Auto Connector" on pages 9 and 20

• With Macintosh notebook computers such as the iBook and PowerBook, always first connect the 01X and mLAN cable then

turn on the power of the 01X, before starting up the computer.

• Are the mLAN settings correct? .................................................................................................. ("The mLAN connection does not work." above)

The Remote Control or Automation features do not work.

• Is the correct DAW software selected in Remote Select? ............................................................................................................................. page 24

• Are the mLAN settings correct? .................................................................................................. ("The mLAN connection does not work." above)

• Are settings on the DAW correct?................................................................................................................................................................. page 24

• Is Port 1 selected for mLAN MIDI transmission/reception?......................................................................................................................... page 21

Cannot change the wordclock.

• Set this with the mLAN Auto Connector when using mLAN.........................................."Settings by mLAN Auto Connector" on pages 9 and 20

• Is the mLAN Auto Wordclock (AUTO W.CLK) setting appropriate?

TOOLS for 01X/Plug-in Effect Installation Guide