Table of Contents
Advertisement
Available languages
Available languages
ASSEMBLY AND ADJUSTMENTS
WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
Blower Tube Assembly (Fig. D)
WARNING:
tube securely held in place. Never reach down into
housing through tube hole.
WARNING:
when you leave the blower unattended or when storing,
checking, adjusting, cleaning, or working on the blower.
1. To attach the blower tube
up the peg
25
on the bottom of the power head
with the notch
24
on the bottom of the blower tube
opening as shown in Fig. D.
2. Push the blower tube
the two blower tube locks
tube
and an audible click is heard.
5
3. Pull on the blower tube
in place.
Concentrator and Broom Tip Assembly (Fig. E)
WARNING:
before you leave the blower unattended or when storing,
checking, adjusting, cleaning, removing/installing
attachments or accessories or working on the blower.
•
Use the concentrator tip
tighter area.
•
Use the broom tip
10
1. Align the concentrator tip
blower tube
5
as shown in Fig. E.
2. Slide the concentrator
3. Slide the locking tab
lock
9
on the blower tube
tab
12
on the bottom of the concentrator tip
broom tip
10
.
4. Pull on the concentrator tip
ensure it is securely held in place.
5. To remove the concentrator tip
lift the locking tab
12
concentrator tip
11
or broom tip
blower tube
5
.
Attaching and Adjusting the Shoulder
Strap (Fig. F)
WARNING:
be slung over one shoulder and not across the body.
To reduce the risk of serious
Do not operate blower without
Always remove the battery
5
to the power head
onto the power head
5
engage the blower
26
5
to ensure it is securely held
Always remove the battery
to target air flow to a
11
to target air flow to a wider area.
11
or broom tip
10
11
onto the blower tube
12
over and down until the tip
5
engages the locking
11
or broom tip
10
11
or broom tip
off of the tip lock
9
and pull the
10
away from the
The shoulder strap should only
Attach the shoulder strap
and adjust for proper balance and support.
1. Snap the shoulder strap latch
located on the power head
2. Adjust the shoulder strap
shoulder and provides proper balance and support.
3. To remove the shoulder strap
strap latch
OPERATION
WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
WARNING:
4
, line
4
blow tube securely in place. Never reach down into
housing through tube hole.
WARNING:
until
4
Always wear respiratory protection. Always wear
hearing protection. Use of rubber gloves and
substantial footwear is recommended when working
outdoors. Keep long hair and loose clothing away from
openings and moving parts. For household use only.
WARNING:
tool off, wait 10 seconds for the fan to stop rotating
before removing the blower tube.
•
Always ensure the blower is switched OFF and the
battery is removed when:
-
You leave blower unattended.
-
Clearing a blockage.
with the
-
Checking, adjusting, cleaning or working on blower.
•
Only use blower in daylight or good artificial light.
5
.
Installing and Removing the Battery Pack
(Fig. G)
11
or
WARNING:
to
the off position before inserting the battery pack.
10
,
nOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
battery pack release button
battery pack out of the tool handle. Insert it into
the charger as described in the charger section of
this manual.
14
to the tool as shown in Fig. F
17
onto the strap mount
4
, as shown in Fig. F.
14
so it fits over your
14
pinch the shoulder
17
and pull it from the strap mount
To reduce the risk of serious
Do not operate blower without
Always wear safety glasses.
Cut Hazard. When turning the
Ensure the tool/appliance is in
15
into the tool handle, align
16
and firmly pull the
English
13
13
.
9
Advertisement
Table of Contents
