Operation - DeWalt DCMWP234 Instruction Manual

2 x 20v max push mower, 20v max self-propelled mower
Table of Contents

Advertisement

Available languages

Available languages

Mulching (Fig. N)

DANGER: Turn unit off and remove safety key and
battery packs.
1. To operate mower in mulching mode, remove the grass
collection bag 
 22 
or side discharge chute 
2. Lift the rear door cover
plug 
 24
fully into the mower.
3. Ensure the pins
35
on the mulching plug
the slots
36
on the mower as shown in Fig. N.
4. Be sure rear door cover
Side Discharge (Fig. O)

DANGER: Turn unit off and remove safety key and
battery packs.
1. To operate mower in side discharge mode, remove the
grass collection bag 
 22 
nOTE: If installed, remove the mulching plug
2. Lift the rear door cover
chute 
 25 
onto the mower as shown in Fig. O.
3. Release the rear door cover
side discharge chute 
operating the mower.
Adjusting Mower Height (Fig. P)
The height of cut is adjusted by the cut height adjust lever
nOTE: If you are not sure which height to mow at, begin
mowing with the cut height adjustment lever
at the highest setting and adjust height down as needed for
your application.
To Set the Height of Cut
1. Pull the cut height adjustment lever
locking notch 
 37 
.
2. Move the cut height adjustment lever
rear of the mower to raise the height of cut.
3. Move the cut height adjustment lever
front of the mower to lower the height of cut.
4. Push the cut height adjustment lever
locking notches 
 37 
.

OPERATION


DANGER: To reduce the risk of serious personal
injury, turn unit off and remove the safety key and
battery packs before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Proper Hand Position (Fig. Q, R)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
 25 
.
21
and slide the mulching
24
is closed.
21
.
24
21
and hook side discharge
21
and ensure the
 25 
is secured in place before
20
positioned
20
out of the
20
towards the
20
towards the
20
into one of the
DCMWP234
Proper hand position requires both hands grasping the main
handle
4
DCMWsP256
Proper hand position requires both hands grasping the main
handle
4
mode; and both hands grasping the main handle, bail handle,
and self drive lever
engage
shown in Fig. R.
READ THIS INSTRUCTION MANUAL
BEFORE OPERATING YOUR MOWER
Refer to Fig. A at the beginning of this manual for a complete
list of components. Save this manual for future reference.

DANGER: Sharp moving blade. Do not operate the
mower in mulching mode if the rear door is not closed
under spring tension as serious injury could result. Take
.
your mower to the nearest service center for repair.

DANGER: Do not operate mower unless handle is
locked into position.

DANGER: Sharp moving blade. Never operate the
mower in bagging mode unless the bag lugs on the
grass collection bag are seated properly on the mower
and the rear door rests firmly against the top of the
grass collection bag as serious injury could result.
20
.

DANGER: Sharp moving blade. Do not operate the
mower in side discharge mode unless the rear side
discharge chute is properly installed with the rear door
cover resting firmly against it.

WARNING: Let the mower work at its own pace. Do
not overload.
Installing and Removing the Battery Packs
(Fig. S)

DANGER: MAKE CERTAIN THE SAFETY KEY IS
REMOVED TO PREVENT ACTUATION BEFORE
REMOVING OR INSTALLING BATTERIES.
This mower is designed to operate on two battery packs
of equal capacity. The mower will not operate on a single
battery pack, and If using different capacity battery packs, the
smaller capacity battery pack, when depleted, will cause the
unit to turn off.
The mower will turn off and the overheat indicator 
blink if the battery pack reaches the high temperature limit,
which can be caused by cutting heavy grass. If this occurs,
allow the battery pack to cool and then resume cutting with
the mower deck set higher.
nOTE: For best results, make sure the battery packs are
fully charged.
To Install the Battery Packs
1. Lift and hold the battery port cover 
battery port 
2. Slide a battery pack 
an audible click is heard (Fig. S). Repeat for the second
battery  pack 
and bail handle
8
as shown in Fig. Q.
and bail handle
8
together when not in self-propel
9
together when in self-propel mode as
 38 
.
 26 
into the battery port 
 26 
.
English
 13 
will
 19 
up to expose the
 38 
until
17

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Dcmwsp256

Table of Contents