Wall Mounting; Assembly And Adjustments - DeWalt DCMWP234 Instruction Manual

English

Wall Mounting

Some D WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE

ASSEMBLY AND ADJUSTMENTS


DANGER: To reduce the risk of serious personal
injury, turn unit off and remove the safety key and
battery packs before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Single Touch Handle Adjustments
(Fig. D, E)
The mower is shipped in the storage position. You will need
to adjust the single touch handle
before continuing.
Raise the Single Touch Handle (Fig. D)
1. To unlock the single touch handle
position, squeeze the handle unlock button
nOTE: The handle unlock button
back of handle support
nOTE: The main handle
both sides of the single touch handle tubes before lifting
the single touch handle
shown in Fig. D,.
2. Raise the single touch handle
Listen for an audible click and ensure the single touch
handle 1 is locked into position before proceeding.
3. Extend the main handle
clicks is heard. The single touch handle
operation position.
nOTE: Take care to not pinch, pull or otherwise stress
the cord 28 .
Adjusting the Main Handle Height
(Fig. F)
The main handle 4 extends to accommodate taller users.
1. To extend the main handle
position, press the handle release button
main handle away from the handle support
audible click is heard, indicating that it is locked into the
lower height position.
nOTE: The handle release button
bottom of handle support
2. To extend the main handle
position, press the handle release button
16
1 to the operating position
1 from the storage
3 .
3 is located on the
2 .
4 must pop out slightly from
1 from the storage position as
1 to the locked position.
4 outward until a set of audible
1 is now in the
4 to the lower height
5 and pull the
2 until an
5 is located on the
2 .
4 to the upper height
5 and pull the
main handle away from the handle support
audible click is heard, indicating that it is locked into the
upper height position.
3. Ensure the main handle
before proceeding.
nOTE: When the batteries
inserted and the bail handle
folding indicator 15
handle 1 is not locked into position.
4. To retract the main handle
postion, press the handle release button
main handle 4 towards the handle support
audible click is heard, indicating that it is locked into
the lower height position.
Storage Mode (Fig. G—L)

DANGER: MAKE CERTAIN THE SAFETY KEY IS
REMOVED TO PREVENT ACTUATION BEFORE
REMOVING OR INSTALLING BATTERIES.

DANGER: Turn unit off and remove safety key and
battery packs.
1. To retract the main handle
button 5 and push the main handle
handle support 2 until two audible clicks are heard,
indicating that both sides of the handles are locked
into position. The main handle
against the handle support.
nOTE: The main handle
windows 29 . If they are not engaged as shown in Fig. G,
press the main handle
until two audible clicks are heard and both sides of
handle windows 29
nOTE: Ensure the two storage latches
the single touch handle
in Fig. J before lowering the single touch handle
the stoarge position.
2. Fold the single touch handle
wheels 32 into storage position. Listen for two audible
clicks as the two storage latches
storage slots 31 as shown in Fig. K.
3. Ensure the single touch handle
position before proceeding.
4. The mower can be stored standing up, with the
collection bag removed, or flat on its wheels as shown
in Fig. L.
nOTE: Take care to not pinch, pull or otherwise stress
the cord 28 .
Grass Collection Bag (Fig. M)

DANGER: Turn unit off and remove safety key and
battery packs.
1. Lift the rear door cover
and place the grass collection bag
so the bag lugs 33 slide into the slots
plastic surfaces of the handle brackets. Then lower the
rear door cover 21 .
nOTE: If installed, remove rear side discharge chute
and ensure the rear door cover
installing grass collection bag
2
4 locks into position
26 and safety key
8 is pulled, the handle
will illuminate if the single touch
4 to the lower height
5 and push the
2
4 , press the handle release
4 towards the
4 must be fully seated
4 must fully engage the handle
4 towards the handle support
are closed as shown in Fig. H.
30 at the back of
1 tubes pop outward as shown
1 towards the front
30 slide into the
1 is locked into storage
21 , remove mulching plug
22 onto the mower
39 on the inside
21 is fully up before
.
22
until an
6 are
until an
2
1 into
24 ,
25