Advertisement
Quick Links
Service Cutting Unit
Groundsmaster
Model No. 30451—Serial No. 401400001 and Up
WARNING
CALIFORNIA
Proposition 65 Warning
Use of this product may cause exposure
to chemicals known to the State of
California to cause cancer, birth defects,
or other reproductive harm.
Safety
Safety and Instructional
Decals
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
1. Grease
1. Height-of-cut adjustment
© 2018—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
4100-D Models 30447 and 30449
58-6520
100-5622
Register at www.Toro.com.
1. Low height-of-cut
adjustment
1. Entanglement hazard, belt—do not operate the machine
with the shields or guards removed; always keep the shields
and guards in place; stay away from moving parts.
decal58-6520
1. Low height-of-cut
adjustment
decal100-5622
Form No. 3426-794 Rev A
Installation Instructions
100-5623
2. High height-of-cut
adjustment
100-6578
104-3579
2. High height-of-cut
adjustment
Original Instructions (EN)
All Rights Reserved *3426-794* A
Printed in the USA.
decal100-5623
decal100-6578
decal104-3579
Advertisement
Related Manuals for Toro 30451
Summary of Contents for Toro 30451
- Page 1 Form No. 3426-794 Rev A Service Cutting Unit Groundsmaster ® 4100-D Models 30447 and 30449 Model No. 30451—Serial No. 401400001 and Up Installation Instructions WARNING CALIFORNIA Proposition 65 Warning Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
-
Page 2: Installation
decal106-4250 106-4250 1. Height of cut decal120-6604 120-6604 1. Thrown object hazard—keep bystanders away from the machine. 2. Cutting/dismemberment hazard of hand, mower blade—stay away from moving parts; keep all guards and shields in place. decal106-4251 3. Cutting/dismemberment hazard of foot, mower blade—stay 106-4251 away from moving parts;... - Page 3 Remove the elastomeric spider from inside each Locate and unplug the cutting-unit wire harness pulley coupler. Retain it for installing on the new from the traction unit wire harness (Figure cutting unit (Figure g013379 Figure 4 1. Wire harness 2. Cable tie Remove any cable ties securing the cutting-unit wire harness to any traction unit components.
- Page 4 g013387 g013380 Figure 8 Figure 6 1. Lift-arm mount (2) 1. Damper 2. Bolt, spacer, and flange Move the cutting unit away from the traction unit. Remove the hair pin cotters and the clevis pins Slide the new cutting unit into position and mount securing the height-of-cut chains to the rear of it to the traction unit by reversing the procedure.
- Page 5 Notes:...
- Page 6 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.
- Page 7 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 8 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.