Related Manuals for Jetson Orbit
Summary of Contents for Jetson Orbit
- Page 1 Orbit Light-Up Kick Scooter. A guide for your ride. IMPORTANT: READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE. MODELS: JORBIT-BKP | JORBIT-BKB...
- Page 3 Jetson's top two riding rules: Be safe. Have fun!
-
Page 5: Table Of Contents
Contents Safety Warnings ......................4 Product Overview ......................6 Specs & Features . -
Page 6: Safety Warnings
Safety Warnings • Before use, please read the user manual and safety warnings carefully, and make sure you understand and accept all the safety instructions. The user will be responsible for any loss or damage caused by improper use. • Before each cycle of operation, the operator shall perform the preoperation checks specified by the manufacturer: That all guards and pads originally supplied by the manufacturer are in proper place and in serviceable condition;... - Page 7 • Prolonged exposure to UV rays, rain and the elements may damage the enclosure materials, store indoors when not in use. MODIFICATIONS Do not attempt to disassemble, modify, repair, or replace the unit or any components of the unit without instruction from the Jetson Care Team. This will void any warranty, and can lead to malfunctions which may cause injury.
-
Page 8: Product Overview
Product Overview HANDLEBAR* KNOB STEM CLAMP DECK (LED LIGHT-UP) STEM (LED LIGHT-UP) LIGHTING CONTROL BUTTON (UNDERSIDE OF DECK) FOLDING LEVER BATTERY COMPARTMENT (UNDERSIDE OF DECK) FRONT WHEEL (MOTION-ACTIVATED LED LIGHT-UP) REAR FOOT BRAKE LOCKING LATCH REAR WHEEL (MOTION-ACTIVATED LED LIGHT-UP) * NOT PRE-ATTACHED;... - Page 9 *OPPOSITE SIDE OF SCOOTER NOTE: IMAGES MAY NOT REFLECT EXACT APPEARANCE OF ACTUAL PRODUCT.
-
Page 10: Specs & Features
Specs & Features · WEIGHT LIMIT: 132 LBS · PRODUCT WEIGHT: 6 LBS · WHEEL SIZE: 4” · FOLDED DIMENSIONS: 24.6”(L) × 9.8”(W) × 7.6”(H) · UNFOLDED DIMENSIONS: 23.5”(L) × 9.8”(W) × 24.6”(H) · DECK DIMENSIONS: 17.5”(L) × 3.5”(W) · HANDLEBAR HEIGHT: 24.6”- 33.3”... -
Page 11: Online Resources
Online Resources Scan for our most updated Orbit onboarding materials and support resources. -
Page 12: Getting Started
THE DIRECTIONS GIVEN IN THIS MANUAL—RIGHT, LEFT, FRONT/FORWARD, AND REAR/BACK—ARE ORIENTED AS THE RIDER WOULD SEE THEM WHEN STANDING ON THE SCOOTER. THE “RIGHT SIDE” OF THE ORBIT, FOR EXAMPLE, IS THE SIDE WHERE THE RIDER’S RIGHT HAND WILL BE. -
Page 13: Unfolding & Folding The Scooter
Unfolding & Folding the Scooter WHEN TO UNFOLD: FOR ASSEMBLY AND RIDING WHEN TO FOLD: FOR STORAGE AND TRANSPORT... - Page 14 1. HOLDING THE LOCKING LATCH STEADY WITH ONE HAND, USE THE OTHER HAND TO LOOSEN THE KNOB BY TURNING IT COUNTERCLOCKWISE FOR 2 - 3 ROTATIONS. LOCKING LATCH *OPPOSITE SIDE OF SCOOTER KNOB...
- Page 15 2. PULL OPEN THE LOCKING LATCH. LOCKING LATCH...
- Page 16 3. PULL THE FOLDING LEVER UP TOWARDS THE TOP OF THE STEM. HOLD IT THERE WHILE YOU RAISE THE STEM UPRIGHT (TO UNFOLD THE SCOOTER) OR LOWER THE STEM TOWARDS THE DECK (TO FOLD THE SCOOTER.) 4. ENSURE THAT THE STEM "CLICKS" INTO PLACE IN THE FOLDED OR UNFOLDED POSITION. STEM FOLDING LEVER DECK...
- Page 17 5. RELEASE THE FOLDING LEVER. 6. HOLD THE LOCKING LATCH STEADY WITH ONE HAND WHILE YOU TIGHTEN THE KNOB BY TURNING IT CLOCKWISE. 7. PUSH THE LOCKING LATCH CLOSED. 8. CHECK THAT THE STEM IS SECURE. TROUBLESHOOTING: IF YOU CANNOT OPEN OR CLOSE THE LOCKING LATCH, THE KNOB MAY BE TOO TIGHT. LOOSEN THE KNOB BY TURNING IT COUNTERCLOCKWISE FOR 1/2 ROTATION AT A TIME UNTIL YOU CAN UTILIZE THE LATCH.
-
Page 18: Attaching The Handlebar
Attaching the Handlebar 1. UNFOLD THE SCOOTER SO THAT THE STEM IS UPRIGHT. 2. UNSCREW THE PRE-ATTACHED BOLT FROM THE NUT IN THE STEM BY TURNING IT CLOCKWISE WITH THE SCREWDRIVER TIP OF THE 2-BIT TOOL. (YOU MAY HAVE TO HOLD THE NUT STEADY WITH A FINGER IN ORDER TO LOOSEN AND REMOVE THE BOLT.) SET THE HARDWARE ASIDE. - Page 19 3. POSITION THE HANDLEBAR BASE OVER THE TOP OF THE STEM SUCH THAT THE RAISED LINE ON THE INSIDE OF THE HANDLEBAR BASE IS IN LINE WITH THE INDENTED CHANNEL ON THE TOP OF THE SCOOTER STEM. HANDLEBAR RAISED LINE *INSIDE OF HANDLEBAR BASE INDENTED CHANNEL STEM...
- Page 20 4. SLIDE THE HANDLEBAR ONTO THE SCOOTER STEM. 5. PUSH DOWN AND ADJUST UNTIL THE HOLES IN THE SIDES OF THE HANDLEBAR BASE ARE ALIGNED WITH THE HOLES ON THE SIDES OF THE STEM. HANDLEBAR HANDLEBAR HOLES STEM HOLES STEM...
- Page 21 6. INSERT THE BOLT THROUGH THE ALIGNED HOLES ON THE RIGHT-HAND SIDE OF THE HANDLEBAR UNTIL THE END OF IT IS VISIBLE THROUGH THE LEFT-SIDE HOLES. IMPORTANT: PLACE THE BOLT ON THE RIGHT SIDE WHEN FACING THE FRONT OF THE SCOOTER FROM RIDING POSITION.
-
Page 22: Adjusting The Height Of The Handlebar
STEM CLAMP 5MM ALLEN KEY BOLT STEM CLAMP LATCH Adjusting the Height of the Handlebar 1. OPEN THE STEM CLAMP LATCH. 2. LOOSEN THE BOLT OPPOSITE THE LATCH TO WIDEN THE CLAMP BY TURNING IT COUNTERCLOCKWISE WITH THE ALLEN KEY TIP OF THE 2-BIT TOOL. - Page 23 3. WHILE PRESSING IN THE STEM PIN, LIFT OR LOWER THE HANDLEBAR UNTIL THE PIN CLICKS INTO ANOTHER STEM PIN HOLE. STEM PIN STEM PIN HOLE...
- Page 24 BOLT STEM CLAMP LATCH 4. CLOSE THE STEM CLAMP LATCH AND TIGHTEN THE BOLT BY TURNING IT CLOCKWISE WITH THE ALLEN KEY. 5. CHECK THAT THE HANDLEBAR IS SECURE. IMPORTANT: THE STEM PIN ALONE WILL NOT KEEP THE STEM SECURE. MAKE SURE THE STEM CLAMP IS TIGHTENED AND CLOSED BEFORE RIDING.
-
Page 25: Inserting The Batteries
Inserting the Batteries YOU WILL NEED 3 AA BATTERIES (NOT INCLUDED) IN ORDER TO USE THE LIGHTS ON YOUR ORBIT. 1. LOOSEN AND REMOVE THE SCREW SECURING THE BATTERY COMPARTMENT COVER ON THE UNDERSIDE OF THE DECK BY TURNING IT COUNTERCLOCKWISE WITH THE SCREWDRIVER TIP OF THE 2-BIT TOOL. -
Page 26: Making Moves
2. Making Moves Riding the Scooter 1. PLACE ONE FOOT ON THE FRONT OF THE DECK FACING FORWARD. 2. USE THE BACK FOOT TO PUSH OF THE GROUND AND PROPEL THE SCOOTER FORWARD. TO COAST: PLACE THE KICKING FOOT ON THE DECK BEHIND THE FRONT FOOT AT A SLIGHT ANGLE. -
Page 27: Using The Brake
Using the Brake PRESS DOWN GENTLY WITH THE REAR RIDING FOOT TO SLOW DOWN. APPLY MORE PRESSURE TO COME TO A COMPLETE STOP. -
Page 28: Using The Led Lights
Using the LED Lights TO TURN ON THE LIGHTS IN THE DECK AND STEM: QUICK-PRESS THE LIGHTING CONTROL BUTTON. NOTE: THE LIGHTS ON THE WHEELS ARE MOTION-ACTIVATED AND LIGHTING WILL ILLUMINATE WHEN THEY ROTATE, EVEN IF THE OTHER CONTROL BUTTON LIGHTS ARE NOT POWERED ON. -
Page 29: Helmet Safety
Helmet Safety A HELMET SHOULD BE WORN BY THE RIDER AT ALL TIMES WHILE ON THE SCOOTER. PROPER POSITIONING: IMPROPER POSITIONING: THE FOREHEAD IS COVERED THE FOREHEAD IS EXPOSED. BY THE HELMET. A FALL COULD RESULT IN SERIOUS INJURY. *WEAR A HELMET, APPROPRIATE CLOTHING, SHOES, AND SAFETY GEAR. AVOID CLOTHING THAT CAN GET CAUGHT INTO OR UNDER THE WHEELS. -
Page 30: Care & Maintenance
Your new Jetson product is warranted against defects in materials and workmanship as indicated on ridejetson.com/warranty for a period of time from the date of original retail purchase when used in accordance with Jetson's user manuals (refer to ridejetson.com/support). Under this warranty, you will be able to direct your claims to Jetson even in situations where you purchased the Jetson Product from one of our authorized retailers. - Page 31 Stay connected. Be sure to follow @ridejetson on social media to learn about fantastic offers, giveaways, and all the latest Jetson news. Loving your ride? Then be sure to leave a review at ridejetson.com/reviews. We can’t wait to hear from you!
- Page 32 Date Code: 07/2023 Document Edition: v2.0 © 2023, JETSON. ALL RIGHTS RESERVED. Manufactured by JETSON ELECTRIC BIKES LLC. No portion of this document, including shape, copy, graphics, and design, may be reproduced or transmitted in any form or by any means.
Need help?
Do you have a question about the Orbit and is the answer not in the manual?
Questions and answers