Blomberg DW 55502 FBI Installation Manual
Hide thumbs
Also See for DW 55502 FBI:
- User manual (47 pages) ,
- Installation manual (26 pages) ,
- Installation manual (25 pages)
Related Manuals for Blomberg DW 55502 FBI
Summary of Contents for Blomberg DW 55502 FBI
- Page 1 Dishwasher Installation Manual DW 24100 B DW 55502 FBI DW 24100 SS DW 55502 SS DW 24100 W DW 25502 W DW 25502 B DW 25502 B DW 25502 SS DW 25502 W DW 55100 FBI DW 55100 SS...
- Page 2 Dishwasher Installation Manual DW 24100 B DW 55502 FBI DW 24100 SS DW 55502 SS DW 24100 W DW 25502 W DW 25502 B DW 25502 B DW 25502 SS DW 25502 W DW 55100 FBI DW 55100 SS...
-
Page 3: Table Of Contents
To prevent accidents, which could cause serious injury or death, as well as machine damage read these instructions before installation and / or use. Contents 1. IMPORTANT SAFETY INSTRUCTIONS 1.1 INSPECT THE DISHWASHER 1.2 HOW TO CONTACT US : 2. TOOLS WHICH MAY BE NEEDED 3. -
Page 4: Important Safety Instructions
INTRODUCTION WARNING Please read this installation manual and When installing the dishwasher, follow particularly the safety instructions completely basic precautions, including the and carefully. They will save you time following: and effort and help to ensure optimum • The dishwasher installation must dishwasher performance. -
Page 5: Inspect The Dishwasher
• Old appliances may contain or Contact the Blomberg Distributor for materials that can be recycled. your State or Province as listed on the Please contact your local recycling Distributor Contact List provided. -
Page 6: Tools Which May Be Needed
2. TOOLS WHICH MAY BE NEEDED 3. MATERIALS WHICH MAY BE NEEDED (Additional materials may be required to comply with local codes) Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. 90° elbow with 3/8” N.P.T. male threads on one leg, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other leg. -
Page 7: Materials Supplied
4. MATERIALS SUPPLIED 4.1 PARTS SUPPLIED Parts for your dishwasher will come in several plastic bags. Check your parts bags shown to make sure you have all the parts as listed to the left. 4.2 MANUAL BAG The dishwasher comes with a manual bag containing: User manual, Installation manual and 4.3 DISHWASHER PARTS BAG 1... -
Page 8: Dishwasher Specifications
5. DISHWASHER SPECIFICATIONS 2 4 ” ( 6 1 2 4 ” ( 6 1 ” m 5.1 TECHNICAL FEATURES Load capacity 14 place settings Permissible water pressure 4.35 - 145 psi (0.3 - 10 bars) Electrical connection 120 V (volts), 12 A (amps), 60Hz (hertz) Total power 1400 W (watts) Heater power... -
Page 9: Enclosure Preparation
6. ENCLOSURE PREPARATION 6.1 ELECTRICAL PREPARATION WARNING The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amperes. 6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS WARNING Dishwasher must be secured to adjacent cabinetry using the mounting brackets... - Page 10 6.3.1 INSTALLING THE FOOT SUPPORTS Supplied (4) 15 / ” (50mm) If the height of the enclosure is 33 7 / 16 ” to 34 1 / 4 ” (850mm - 870mm) use short supports as shown in the figure. 15 / ”...
-
Page 11: Installing The Side Trim Strips
Adjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height. Adjust the rear foot level with a screwdriver to balance and raise the dishwasher to the enclosure height. Notice : • Make sure the dishwasher is plumb and notice dishwasher can be placed with a small clearance under the counter top. -
Page 12: Preparing The Water Connection (A)
6.5 PREPARING THE WATER CONNECTION (A) Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections must be made before the water line is connected to the dishwasher’s water inlet valve. Water can also be supplied to the dishwasher by using a flexible braided hose line. -
Page 13: Drain Preparation
6.6 DRAIN PREPARATION The dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figure A, B, C). Notice : • Either one of the above methods must be used or the dishwasher will not operate properly. -
Page 14: Steam Protection Foil
6.7 STEAM PROTECTION FOIL Steam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it is required to use a steam protection foil to prevent any steam from collecting on the underside of the counter top. 6.6.2 FITTING THE PROTECTION FOIL Before applying the steam protection foil to the underside of the countertop, clean the area with... -
Page 15: Placement Of Dishwasher Into The Opening
7. PLACEMENT OF DISHWASHER INTO THE OPENING Now place the dishwasher into the opening and get ready to connect all hoses and electrical connections. CAUTION Make sure all hoses are pulled through the side opening of the cabinet, no hoses are kinked and all slack is taken out as shown in the above figure. -
Page 16: Electrical Connection
7.1.2 WATER SUPPLY CONNECTION Water supply may be connected to the dishwasher in one of two ways: • With metal braided hose. • With copper tubing. 7.1.3 BRAIDED HOSE/COPPER TUBING After connections are made turn on the water supply to check for leaks. CAUTION • Hot water supply line: Use minimum 3/8”... -
Page 17: Readjusting Foot Levels
7.3 READJUSTING FOOT LEVELS Now that the dishwasher is in the cabinet you must readjust the feet to bring the dishwasher up to the required height and attach it underneath the countertop. 1. Readjust the front foot levels with adjusting wrench to balance the dishwasher and raise it up under the countertop, make sure the unit is level. - Page 18 Lock the toe kick brackets as shown with the plastic tab in the figure C by pushing the plastic tab on the dishwasher into the teeth of the bracket (C). 3. Now attach the toe kick to the bracket with the two (Ø...
-
Page 19: Installing The Outer Door (Dw 55100 Fbi)
7.5 INSTALLING THE OUTER DOOR (DW 55100 FBI, DW 55502 FBI) Measure the height and width of the enclosure (Figure A) and the toe kick. Determine how big the wooden door can be. For example if the height is 33 7 / 8 ” (860mm) and if the toe kick is 3 15 / 16 ”... - Page 20 4. Place the plastic mounting brackets over the marked holes and the side tabs must be flush with the edge of the wooden door (Figure D). 5. Attach the two mounting brackets to the wooden door with 4 screws (Ø 1 / 8 ” x 5 / 8 ” (Ø (3,5mm) Ø...
- Page 21 7. Open the door and remove the two caps and two screws inside the door at position 1 and 3 (Figure C). 8. Using the four screws Ø 3 / 16 ” x 1 11 / 16 ” (Ø 4mm x 43mm) provided, attach the wooden door to the dishwasher at position 1 and 3 (Figure A).
- Page 22 ADJUSTING DOOR TENSION WITH CUSTOM WOODEN DOOR (DW 55100 FBI, DW 55502 FBI) Check the door tension of the dishwasher: If the door closes too quickly or if the door falls open, the spring tension needs to be adjusted.
- Page 23 Notice : If you have a European kitchen or want to install a wooden toe kick to match your kitchen, please refer to one of the two drawings given below. Follow the same instructions on the brackets as for the removable toe kick. Installation should be done following the steps illustrated in the figures A, B, C, D respectively.
-
Page 24: Installer Checklist
8. INSTALLER CHECKLIST 10. SELF HELP HINTS: Your installer must have completed and The screen does not come on: checked the following: • Check to make sure the breaker to the • The dishwasher is square and level. dishwasher is in the on position. • The dishwasher is fastened securely to the • Check to make sure that the Supply cord cabinetry. - Page 25 www.blomberginternational.com info@blomberginternational.com...