Advertisement
Quick Links
Rear PTO Kit
Heavy-Duty Workman
Model No. 07419
For machines with serial numbers 239999999 and before, decal 93-9861 is not included in the kit. You must
purchase decal 93-9861 separately and apply it.
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
1. Engage PTO
2. Disengage PTO
3. Rear PTO
4. Warning
© 2022—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
93-9861
5. Entanglement hazard,
shaft
6. Read the Operator's
Manual.
7. Keep bystanders away
from the machine.
Register at www.Toro.com.
®
Vehicles
1. Entanglement hazard—keep away from moving parts; keep
all guards and shields in place.
decal93-9861
Form No. 3457-578 Rev A
Installation Instructions
93–9862
*3457-578*
Original Instructions (EN)
Printed in the USA
All Rights Reserved
decal93-9862
Advertisement
Related Manuals for Toro 07419
Summary of Contents for Toro 07419
- Page 1 Form No. 3457-578 Rev A Rear PTO Kit Heavy-Duty Workman ® Vehicles Model No. 07419 Installation Instructions For machines with serial numbers 239999999 and before, decal 93-9861 is not included in the kit. You must purchase decal 93-9861 separately and apply it. Safety...
-
Page 2: Installation
Installation Preparing the Machine No Parts Required Procedure Park the machine on a level surface. For machine models with a utility bed, perform g009164 the following: Figure 2 Raise the bed until the lift cylinders are fully 1. Bed support 3. - Page 3 Remove the 6 screws that secure outside edge of the center console cover plate to the frame and remove the cover plate (Figure g022071 Figure 4 1. Terminal cover 3. Battery post 2. Positive terminal 4. Battery g028745 Figure 6 Installing the PTO Controls 1.
- Page 4 Installing the PTO Cable No Parts Required Routing the PTO Cable Route the PTO cable under the rear of the lever support bracket. g028746 Figure 7 Connect the PTO cable clevis to the hole in PTO lever with a clevis pin and a cotter pin (Figure 1.
- Page 5 Connecting the PTO Cable Important: Accomplish the installation steps in Connecting the PTO Cable (page 5) only when installing the kit on a machine with a serial number prior to 239999999; otherwise skip to 4 Installing the PTO to the Transaxle (page Note: Some of the parts required to install this kit on machines with serial numbers prior to 239999999...
- Page 6 Clean console plate and install the operation decal to the console next to PTO lever, locating the decal as shown in Figure g028752 Figure 13 g028754 Figure 15 1. PTO lever 4. PTO lever support 1. Console 2. Operation decal 2.
- Page 7 Note: When mounting the PTO assembly, make sure that O-ring is positioned properly in groove on transaxle. If O–ring is damaged, replace it. g028755 Figure 16 1. Transaxle cover plate 3. Fitting 2. Hydraulic hose Remove the fitting from cover plate. g028757 Figure 18 Install the fitting into the front of the new PTO...
- Page 8 pin will drop freely through the aligned mounting holes in the clevis and lever arm (Figure 19). Secure the clevis pin with the cotter pin, tighten jam nut that secures the cable to cable clevis, Completing the PTO and tighten the jam nuts that secure the cable to the bracket.
-
Page 9: Description Of Operation
Description of Operation Operation The PTO takes power from the engine, through the transaxle, and supplies power through a standard WARNING 540 rpm-splined shaft at the rear of the vehicle. PTO The vehicle may move unexpectedly if the power can be used for both mobile and stationary PTO is engaged and the vehicle is shifted into attachments. - Page 10 Mobile PTO Operation Stationary PTO Operation Important: Important: When operating the PTO, the machine When operating the PTO, the machine must not be moving when PTO is started. must not be moving when PTO is started. Engage the parking brake. Engage the parking brake.
- Page 11 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 12 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.