Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Samsung SHP-DP920
Summary of Contents for Samsung SHP-DP920
- Page 1 SHP-DP920 Samsung SDS Door Lock User and Reference Guide Ver1.0.0...
-
Page 2: Product Specifications
Product Specifications Item Spec. Exterior Unit 87.5mm(W)×391.8mm(H)×64.5mm(D) Size Interior Unit 88.5mm(W)×357.6mm(H)×69.3mm(D) Voltage 4 AA Alkaline 1.5V Batteries (LR6) (6V) Emergency Power Source 9V Battery(6LF22) (Separately sold) 10 Months (based on an average of 6 uses per day) Battery Life Support Card Standard ISO14443A (Mifare®... - Page 3 Interior Parts Mortise...
- Page 4 The Samsung SDS Z-Wave Door Lock is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to communicate to other security enable Z-Wave Plus products. The Samsung SDS Z-Wave Door Lock must be used in conjunction with a Security Enabled Z-Wave Controller in other to fully utilize all implemented functions.
- Page 5 Z-Wave plus info (V2) Z-Wave Plus Version : 02 Role Type : LSS (Listening Sleeping Slave) Node Type : Z-Wave Plus Node Manufacturer Specific (V2) Device ID Type : 01(Serial Number) Device ID Data Format : 01 (Binary) Device ID Data Length Indicator : 16 Device ID : XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX ...
- Page 6 ⋅ Bluetooth : 21 ~ 30 ⋅ Fingerprint : 31 ~ 130 Association (V2) & Association Group Information (V1) Lifeline between controller and SHP-DP920 Supported command classes : Battery report, Notification report, and Device Reset Locally notification Maximum supported node is 1EA ...
- Page 7 0x01 Samsung SDS This value can be used when the device is connected with platform of Samsung SDS. This function is not related to Z-Wave CC. - 0x02 : Command for disable which is set by platform of Samsung SDS.
- Page 8 Value of Security Function is not changed by this command. This parameter is supported to ‘Configuration Get Command’ only. This value set by platform after device connected with platform of Samsung SDS. Firmware update meta data (V2) Manufacturer ID : 0x022E (Samsung SDS) ...
-
Page 9: Basic Functions
Note : Pressing the [REG] button is only available while the door is open. (Deadbolt must be unsecured.) Basic Functions 1. Factory Reset All registered Master/User data will be deleted, and Master PIN Code is set to ‘1234’. Also Z- Wave Door Lock is being removed from a network. -
Page 10: Registering A Fingerprint
4. Registering a Fingerprint You can register up to 100 fingerprints. ① Press the [REG] button. (Ding dong) ② When LED light on the Fingerprint Reading Panel is on, touch the panel with the fingerprint to be registered. When a “ding” sound is heard and LED light goes off, then remove the finger. - Page 11 (Success : Ding dong dang, Fail : Ding dong Ding dong) 7. Opening the Door with a PIN Code ① Touch the [Touchscreen]. ② Enter the PIN Code and press the [*] button. ③ The door opens whithin one second. 8.
- Page 12 Addtional Function 11. Activation/Deactivation of the Bluetooth Mode After the Bluetooth mode is activated, accessing the door lock from the outside or touching its number pad can authenticate the registered Bluetooth smartphone to open the door. The Bluetooth mode is activated by default. ①...
-
Page 13: Sound Setting
15. Intrusion Detection Function When the Interior Unit is forcibly detached while the door is locked, it is detected by the door open/close sensor, the alarm sounds. The Intrution Detection function is a basic function and cannot be disabled. 16. Sound Setting The sound that is generated when the number buttons are pressed, when the door is locked or when the locked door is unloced, can be set according to the user’s preference.