Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Power Tools Accessories
  5. 132-4193
  6. Installation instructions manual

Toro 132-4193 Installation Instructions Manual

Automated row selection kit 2024 directional drill
Hide thumbs

Advertisement

Quick Links

Download this manual
Automated Row Selection Kit
2024 Directional Drill
Model No. 132-4193
This product contains a chemical or chemicals known to the State of California to
Safety
Safety and Instructional Decals
© 2015—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
WARNING
CALIFORNIA
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
125-6184
Register at www.Toro.com.
Form No. 3397-156 Rev A
Installation Instructions
Original Instructions (EN)
All Rights Reserved *3397-156* A
Printed in the USA

Advertisement

loading

Related Manuals for Toro 132-4193

Summary of Contents for Toro 132-4193

  • Page 1 Form No. 3397-156 Rev A Automated Row Selection Kit 2024 Directional Drill Model No. 132-4193 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.

  • Page 2: Loose Parts

    Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Rotary sensor Inner sensor bracket Outer sensor bracket Bolt (M4-10 mm) Bolt (M8-1.25 x 20 mm) Locknut (M8) Cam assembly Install the rotary sensor. Flange nut Bolt (M10-1.5 x 30 mm) Bolt (M10-1.5 x 35 mm)
  • Page 3 Installing the Rotary Sensor Parts needed for this procedure: Rotary sensor Inner sensor bracket Outer sensor bracket Bolt (M4-10 mm) Bolt (M8-1.25 x 20 mm) Locknut (M8) Figure 2 Cam assembly 1. Cam assembly Flange nut Bolt (M10-1.5 x 30 mm) 3.
  • Page 4 11. Assemble the new cam assembly using the wear pads and bolts from the previous cam assembly and 14 flange nuts and 2 locknuts (M8) included in this kit (Figure 12. Install the new cam assembly using the 3 bolts (M10-1.5 x 30 mm), 1 bolt (M10-1.5 x 35 mm), and 1 locknut (M10) as shown in Figure...
  • Page 5 Figure 8 1. Bolt (existing) 4. Spacer (existing) 2. Inner sensor bracket 5. Nut (existing) g0293 51 3. Flat washer (new) Figure 9 1. Nut (M10-1 mm) 5. Bolt (M4-10 mm) 17. Using a thread-locking compound on the bolt, install 2.
  • Page 6 Moving the Proximity Sensor and Replacing the Rod-Loading Adjustment Hardware Parts needed for this procedure: Bolt (M8-1.25 x 40 mm) Figure 10 Bolt (M8-1.25 x 30 mm) 1. Mark on the bolt 2. Sensor wires Bolt (M5-0.08 x 25 mm) Nut (M5-0.08 mm) 27.
  • Page 7 Figure 14 1. Measure here on both 3. Bolt (M8–1.25 x 30 mm) sides of the machine 2. Bolt (M8–1.25 x 40 mm) 7. Replace the top bolts with the long bolt (M8-1.25 x 40 mm) (Box B of Figure 14).

  • Page 8: Installing The Wiring Harness

    3. Route the harness lead marked starter along the wiring harness of the machines to the starter on the engine and attach the ring terminal to the same location as the current wire (Box B of Figure 17). Installing the Wiring Harness Parts needed for this procedure: Wiring harness Cable ties...
  • Page 9 Figure 20 Figure 18 Wiring harness with cable ties 15. Install the latest version of software into the machine and complete the tests described in that software 7. Route the connectors marked Setup Valve up to the update. 9-section valve block to the top solenoid marked Setup Valve (Figure 18).
  • Page 10 10. Clean the sealing surfaces of the pump housing and control housing. 11. Install the control housing onto the pump using the new gasket. Important: The control linkage pin on the control must be inserted into the swash-plate link in the pump.
  • Page 11 Checking the Neutral Adjustment 1. Install a hydraulic test port and a 1000 psi gauge in each of the displacement control ports (M4 and M5). Installing the Thrust Motor Anti-Rotation Supports Parts needed for this procedure: Adjustment block Brace Nut (3/8-16 inch) Bolt (3/8-16 x 1 1/4 inch) Bolt (3/8-16 x 1 inch) Spacer...
  • Page 12 Figure 28 Side View – Front mounts (motors removed) Figure 25 1. Weld the front motor blocks 1/8 inch over the edge. Side view Figure 29 Side View – Rear Mounts (Aligned with the edge; motors removed) 2. Remove and discard the existing bolt and washer from the thrust motor (Box A of Figure 30).
  • Page 13 9. Torque the 8 bolts (M12) to 90 to 112 N-m (67 to 83 ft-lb). 10. Paint the welded area. Installing the Proximity Switch Bracket Parts needed for this procedure: Bracket Plate flag Bolt (M5-0.08 x 25mm) Nut (M5) Cable tie Procedure Figure 30 1.
  • Page 14 Figure 34 Current routing Figure 32 2. Weld the plate flag to the carriage assembly 5 7/8 inches away from the spindle end of the carriage assembly as shown in Figure Figure 35 Existing rear sensor 1. Existing sensor 5. Tag the sensor and wiring harness to note which part of the harness goes to which sensor (Figure 36).
  • Page 15 7. Remove the 2 proximity sensors from the mounting plate and discard the hardware (Figure 36). 8. Loosely secure the 2 proximity sensors to the bracket with 4 bolts (M5) and 4 nuts (M5) as shown in Figure Figure 39 1.
  • Page 16 Figure 41 1. Rear bracket 2. Front bracket B. Adjust the pipe-return proximity sensor until the light illuminates (Figure 40). C. Tighten the bolts and nuts on the sensor. Figure 43 D. Torque the bolts to 791 to 971 N-cm (70 to 86 1.