Sealey SUPERMIG275.V2 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear a
instructions welding helmet
Arc rays can Electric shock
burn eyes and from welding
Injure skin electrodes can
kill
1. SAFETY
1.1. ELECTRICAL SAFETY
‰
WARNING! It is the user's responsibility to read, understand and comply with the following:
1.1.1. You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads,
plugs and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of
appropriate safety devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We
also recommend that an RCD (Residual Current Device) is used with all electrical products. It is particularly important to use an RCD
together with portable products that are plugged into an electrical supply not protected by an RCCB. If in doubt consult a qualified
electrician. You may obtain a Residual Current Device by contacting your Sealey stockist. You must also read and understand the
following instructions concerning electrical safety.
The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
1.1.2.
electrician, using a Portable Appliance Tester (PAT), at regular intervals.
1.1.3. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance, and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.4. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply. See 1.1.1. & 1.1.2.
above and use a Portable Appliance Tester (PAT).
1.1.5. Ensure that cables are always protected against short circuit and overload.
1.1.6. Regularly inspect power supply leads, plugs and all electrical connections for wear and damage. Inspect power connections to
ensure that none is loose.
IMPORTANT: Ensure the voltage marked on the product is the same as the electrical power supply to be used and check that plugs
are fitted with the correct capacity fuse. A 13 amp plug may require a fuse smaller than 13 amps for certain products,
see fuse rating at right.
8
DO NOT pull or carry the powered appliance by its power supply lead.
8
DO NOT pull power plugs from sockets by the power cable.
8
DO NOT use worn or damaged leads, plugs or connections. Immediately replace or have repaired by a
qualified electrician. A U.K. 3 pin plug must be fitted according to the following instructions.
(UK only - see diagram at right).
Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the green/yellow earth wire to the earth terminal.
b) Connect the brown live wire to live terminal.
c) Connect the blue neutral wire to the neutral terminal.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the
cable external insulation extends beyond the cable restraint and that the restraint is tight.
1.1.7. Cable extension reels. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD
fitted is recommended since any product which is plugged into the cable reel will be protected. The section of the cable on the cable
reel is important and should be at least 1.5mm², but to be absolutely sure that the capacity of the cable is suitable for this product
and for others that may be used in the other output sockets, we recommend the use of 2.5mm² section cable.
© Jack Sealey Limited
270AMP PROFESSIONAL MIG WELDER WITH
BINZEL® EURO TORCH
MODEL NO:
Wear protective Wear safety
gloves footwear
Breathing Electromagnetic
fields can cause
welding fumes
can be pacemaker
hazardous to malfunction
your health
Original Language Version
SUPERMIG275.V2
Wear protective Keep away
clothing from rain
Welding sparks Caution
can cause required
explosions or
fire
Electrical shock Keep clear
hazard Of fan
Replacement
fuse rating: 13A
Supermig275.V2 Issue 1 10/01/22