Table of Contents
Advertisement
Available languages
Available languages
•
Do not cut small brush and saplings with the pole saw. Slender
matter may catch in the chain and be whipped toward you.
This could also pull you off balance.
•
Do not operate in poor lighting.
•
Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance or exposure to hot
surfaces.
•
Keep all parts of your body away from any moving part.
•
Do not, under any circumstance, use any attachment or
accessory on this product, which was not provided with the
product, or identified as appropriate for use with this product
in this instruction manual.
•
Inspect pole saw before each use and after dropping or other
impacts. Ensure there are no significant defects or damage.
Do Not Operate Pole Saw:
-
while under the influence of alcohol, medication, or drugs.
-
in rain or in damp or wet areas.
-
where highly flammable liquids or gases are present.
-
if pole saw is damaged, adjusted incorrectly, or not fully
and securely assembled.
-
if trigger does not turn pole saw on and off. Chain must
stop moving when you release trigger. Have faulty switch
replaced by authorized service center. See Accessories
under Maintenance.
-
while in a hurry.
-
while in a tree or on a ladder.
-
while on aerial booms, buckets or platforms.
-
during high wind or storming weather.
GENERAL SAFETY RULES
DANGER: Shock Hazard. Serious injury or death from
electrocution if power lines are contacted. Never use near
any electrical source, wires, or power lines.
WARNING: For safe operation read and understand
owner's manual. Wear face shield (and/or safety glasses)
and hard hat to protect against falling debris. Always have
a clear work area, retreat path, and be aware of limb/
branch location to avoid falling limbs and debris. Keep
bystanders 15 m away when operating saw. To reduce the
risk of electric shock do not use on wet surfaces. Do not
expose to rain. Store indoors.
•
To protect yourself from falling branches do not stand directly
under the branch or limb being cut. This unit should not be held at
an angle over 60° from ground level.
•
Keep the handles dry, clean, and free of oil.
•
Before you start the unit, make sure the chain is not contacting
any object.
•
Make sure the cutting chain has stopped before setting the unit
down.
Service
•
Tool service must be performed only by qualified repair
personnel. Service or maintenance performed by unqualified
personnel could result in a risk of injury. Refer to the
Maintenance section of this manual.
•
When servicing a tool, use only identical replacement
parts. Follow instructions in the Maintenance section of
this manual. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of electric shock
or injury.
Guard Against Kickback
WARNING: KICKBACK may occur when the nose or tip of
the guide bar touches an object, or when the wood closes
in and pinches the saw chain in the cut. Tip contact in
some cases may cause a lightning fast reverse reaction,
kicking the guide bar up and back towards the operator.
Pinching the saw chain along the top of the guide bar may
push the guide bar rapidly back towards the operator.
Either of these reactions may cause you to lose control of
the saw which could result in serious injury to user.
THE FOLLOWING PRECAUTIONS SHOULD BE
FOLLOWED TO MINIMIZE KICKBACK:
•
Grip pole saw firmly. Hold the saw firmly with both hands
when the unit is running. Use a firm grip with thumbs and
fingers encircling the saw handle and pole.
•
Do not overreach.
•
Keep proper footing and balance at all times.
•
Don't let the nose of the guide bar contact a log, branch,
ground or other obstruction.
•
Do not extend pole saw handle above shoulder height.
•
Use devices such as reduced kickback chain, chain braking
system and special guide bars that reduce the risks associated
with kickback.
•
Only use replacement bars and chains specified by the
manufacturer or the equivalent.
•
Never let the moving chain contact any object at the tip of the
guide bar.
•
Keep the working area free from obstructions such as other
trees, branches, rocks, fences, stumps, etc. Eliminate or avoid
any obstruction that your saw chain could hit while you are
cutting through a particular log or branch.
•
Keep your saw chain sharp and properly tensioned. A loose or
dull chain can increase the chance of kickback. Check tension
at regular intervals with the motor stopped and battery
removed.
•
Begin and continue cutting only with the chain moving at
full speed. If the chain is moving at a slower speed, there is a
greater chance for kickback to occur.
•
Cut one branch at a time.
•
Use extreme caution when re-entering a previous cut. Engage
spiked bumpers into wood and allow chain to reach full speed
before proceeding with cut.
•
Do not attempt plunge cuts or bore cuts.
•
Watch for shifting branches or other forces that could close a
cut and pinch or fall into chain.
English
9
Advertisement
Table of Contents
