Table of Contents
Advertisement
If the settings of MCC and MNC are changed and the added
access point disappears from the screen, reset the settings or
set the access point manually.
Resetting an access point
Reset an access point to default setting.
1
In the home screen,
[More...]/[Mobile networks]/[Access Point
Names]/[z]/[Reset to default]
When sp-mode is not subscribed or if you fail to make
automatic setting of an access point due to signal status such
as outside the service area, you are required to set the access
point again manually.
sp-mode
sp-mode is an ISP owned by NTT DOCOMO for smartphones.
In addition to the Internet connection, mail service with the
same address you use on i-mode (@docomo.ne.jp) or other
services are available. sp-mode is a paid service that requires
subscription. For details on sp-mode, refer to the DOCOMO
website.
Wi-Fi settings
If you use Wi-Fi function of the tablet, you can use mail or
Internet by connecting to access points of your home,
corporate network or public wireless LAN service.
Radio interference with Bluetooth devices
Wireless LANs (IEEE 802.11b/g/n) use the same frequency
band (2.4 GHz) as Bluetooth devices. Therefore, using the
wireless LAN device near a Bluetooth device may cause radio
interference, lowering of communication speed, noise or
connection failure. In this case, turn off the Bluetooth device or
keep the tablet and the wireless LAN device at least
approximately 10 m away from the Bluetooth device.
Packet communication is also available while Wi-Fi is set to [ON].
Wi-Fi connection is prioritized while Wi-Fi connection is set, but
the connection is automatically switched to that of LTE/3G/GPRS
network once Wi-Fi connection is terminated. Note that packet
communication charges may be incurred in this case.
Refer to the manual of your wireless LAN base unit when using
the access point at home etc.
Operate access point registration near the access point.
If you use the docomo service by using Wi-Fi function, set a
docomo ID in advance. In the home screen,
[docomo service/cloud]/[docomo ID設定] (Set docomo ID) to
set it.
1
In the home screen, [R]/[Settings]/[Wi-Fi]
2
Slide [OFF] to the right
3
Select an access point
: If you select an access point protected by security, enter the
password (security key) and select [Connect].
: To register access points manually: [ADD
enter the network SSID/set security/[Save]
: WPS compatible access points can be easily registered. In
the home screen, [R]/[Settings]/[Wi-Fi]/[EASY
SETTINGS]/[WPS Push Button]/[WPS Pin Entry] to
register an access point.
[R]/[Settings]/
[R]/[Settings]/
NETWORK]/
: Alternatively, in the home screen,
[EASY SETTINGS]/[AOSS] to connect to an access point.
Follow the instructions on the screen and operate after this
step.
When you select an access point and connect to it with a wrong
password (security key), [Avoided poor Internet connection],
[Authentication problem] or [Connected (Limited)] is displayed.
Confirm the password (security key). When [Avoided poor
Internet connection] or [Connected (Limited)] is displayed after
entering the correct password (security key), you may not have
acquired the correct IP address. Connect to the access point
again after confirming signal status.
The registration process using WPS takes a few minutes. After
completion of the registration of the access point, check that the
proper connection to the access point is acquired.
As for the manual registration of an access point, this function
supports WEP, WPA/WPA2 PSK and 802.1xEAP as the
security setting.
Detailed settings
■
1
In the home screen,
[z]/[Advanced]
2
Select an item
Network
notification: Set whether to display a notification
icon when an open network is detected.
･ Set it after setting Wi-Fi to [ON].
Wi-Fi sleep
policy: Set when to switch the Wi-Fi function to
the sleep mode.
Scanning always
the location information service and other apps even when
Wi-Fi is set to [OFF].
Avoid poor
connections: Set whether to use the Wi-Fi
function only when stable Internet connections are available.
Wi-Fi frequency
Install
certificates: Install certificates.
MAC
address: Confirm the MAC address.
IP
address: Confirm the IP address.
Disconnecting
■
1
In the home screen, [R]/[Settings]/[Wi-Fi]
2
Select the connected access
[Disconnect]
: Disconnect with the password retained. The access point
may be automatically connected again such as when the
display is turned on.
Tethering
You can use the tethering function that connects Wi-Fi
compatible devices, or PCs etc. connected via Micro USB
Cable 01 (sold separately) or Bluetooth communication to the
Internet by using the tablet as an access point.
You can connect up to 12 devices in total at the same time: a PC
connected via Micro USB Cable 01, ten Wi-Fi compatible devices
and a Bluetooth device.
The tablet supports Bluetooth tethering via DUN profile. Before
using Bluetooth tethering, register the other party's Bluetooth
device in advance (nP. 76 "Using Bluetooth function").
As for the settings on the Bluetooth device, refer to its manual.
1
In the home screen,
[More...]/[Tethering]
23
[R]/[Settings]/[Wi-Fi]/
[R]/[Settings]/[Wi-Fi]/
available: Set whether to scan networks by
band: Set the frequency band to use.
point/
[R]/[Settings]/
Before Using the Tablet
Advertisement
Table of Contents
