Advertisement
Interface Description/ 接口说明
1
2 3
12
11
NO.
Item
Description
序号
名称
说明
Indicates the GE-SFP optical interface that supports single-mode optical fibers. Depending on the SFP
optical module type, the interface supports the single-fiber bidirectional (Tx: 1310 nm/Rx: 1490 nm or
1
SFP
Tx: 1490 nm/Rx: 1310 nm) or dual-fiber bidirectional (1310 nm) optical fiber.
GE-SFP光模块接口。该接口支持单模光纤，视配套SFP光模块类型，可以支持单纤双向（Tx：1310nm/Rx：
1490nm或Tx：1490nm/Rx：1310nm）或者双纤双向（1310nm）。
System running status indicator.
2
STAT
系统运行状态指示灯。
Reset button. To restart the device, hold down the RST button for less than 3s. To restore the device to
factory defaults, hold down the RST button for at least 3s during the device running or hold down the
3
RST
RST button, power on the device, and keep holding down the RST button for more than 5s.
重置按钮。运行时按住RST键短于3秒重启设备；运行时按住RST键不短于3秒或者按住RST键后上电并持续按住
RST键不短于5秒后恢复出厂配置。
Indicator Description/ 指示灯说明
STAT Status Indicator
STAT状态指示灯
Off
The power is disconnected.
灯灭
电源未连接。
Orange
The system is starting.
橙色
系统正在启动。
Green
The system is running properly.
绿色
系统运行正常。
Red
An exception occurs in the system.
红色
系统有异常。
NOTE/ 说明
When the IPC is enabled, the indicator is changed to: Off → Orange → Green.
IPC启动时，STAT指示灯的变化为：灯灭→橙色→绿色。
4
5
6
7
10
9
8
LINK/ACT Status Indicator
LINK/ACT状态指示灯
Off
The optical port is disconnected.
灯灭
光口未连接。
On (Yellow green)
The optical port is connected.
灯亮（黄绿色）
光口已连接。
NO.
Item
Description
序号
名称
说明
Network interface. Support power over Ethernet (PoE). When the power input interface and PoE
4
POE
interface are connected at the same time, PoE is preferred.
网络接口。支持PoE供电。当电源输入接口和PoE同时连接时，优先PoE供电。
Interface for connecting the ground cable.
5
GND
用于连接接地线。
Automatic back focus (ABF) button. After the ABF button is pressed, automatic focus is performed.
6
ABF
自动后焦调整按钮。按下ABF按钮实现自动聚焦。
Power input interface. Support 12 V DC (9.0 V to 15.0 V) and 24 V AC (18.0 V to 29.9 V) power
DC 12V/
7
supply.
AC 24V
电源输入接口。支持DC 12V（9.0V～15.0V）和AC 24V（18.0V～29.9V）。
Audio input/output port.
8
AUDIO
音频输入输出接口。
Analog video output interface. The interface supports only D1 video output.
9
VIDEO
模拟视频输出接口。该接口仅支持以D1分辨率输出视频。
RS485 interface (D-, D+).
RS485
RS485接口（D-，D+）。
Alarm output interface (1A, 1B).
ALM OUT
告警输出接口（1A，1B）。
10
Alarm input interface (D indicates the positive pole. G indicates the negative pole.).
ALM IN
告警输入接口（D为正极，G为负极）。
SD card slot that supports only Micro SD cards of Class 6 or higher classes. You can replace a Micro
SD card only when the device is powered off. When a Micro SD card is used for the first time, log in
11
SD CARD
to the web page of the device and format the Micro SD card. For details, see Configuration Guide.
SD卡卡槽，仅支持Micro SD卡（Class 6及以上）。请在设备断电的情况下插拔SD卡，否则会造成系统异
常。首次使用时，请登录设备Web客户端，格式化SD卡，操作方法请参见《配置指南》。
Optical port status indicator.
12
LINK/ACT
光口状态指示灯。
Prepare for Installation Tools/ 准备安装工具
PVC insulation tape
Wiring terminal
绝缘胶带
接线端子
Hammer drill (for mounting
a camera on the ceiling or
BNC Female to RCA Male
wall)
Adapter
冲击钻（吊顶和墙壁安装时使
BNC母头转RCA公头
用）
Socket wrench (M6)
Cable stripper
套筒扳手（M6）
剥线钳
Glass cement
Marker
玻璃胶
记号笔
Claw hammer (for mounting
Phillips screwdriver (There
a camera on the ceiling or
are two head models: 1#
wall)
and 2#)
羊角锤（吊顶和墙壁安装时使
十字螺丝刀（刀头型号为：1#
用）
和2#）
RJ-45 connector crimping
tool
Waterproof tape
水晶头压线钳
防水胶带
Advertisement
