Advertisement
Roll to roll function related parameters
Pr.
GROUP
1027
A910
1028
A911
1029
A912
1030
A913
1031
A914
1032
A915
1033
A916
1034
A917
1072
R304
1113
H414
D403
1114
R305
1211
R171
1215
R172
1217
R173
1219
R170
4
1222
R175
1223
R174
1226
R176
1227
R103
1230
R002
1231
R010
1232
R011
1233
R012
1234
R013
1235
R020
1236
R021
1237
R022
1238
R023
1239
R024
1240
R025
1241
R026
1242
R027
1243
R600
1244
R601
1245
R042
1246
R040
1247
R000
1248
R001
1249
R043
1250
R260
1251
R261
1252
R070
1253
R071
1254
R072
1255
R073
1256
R074
1257
R075
1258
R076
1259
R077
1262
R005
1263
R006
1264
R421
1265
R230
1266
R231
1267
R232
1268
R233
32
1269
R234
1270
R235
Refer to the FR-A800-R2R Instruction Manual (Roll to Roll Function Manual) for the instructions to set each parameter.
Name
Analog source selection (1ch)
Analog source selection (2ch)
Analog source selection (3ch)
Analog source selection (4ch)
Analog source selection (5ch)
Analog source selection (6ch)
Analog source selection (7ch)
Analog source selection (8ch)
Tension reverse selection
Speed limit method selection
Torque command reverse selection
Tension PI gain tuning timeout time
Limit cycle output upper limit
Limit cycle hysteresis
Tension PI gain tuning start/status
Target amplitude
Manipulated amount for operation
Tension PI gain tuning response level
setting
Dancer / tension feedback input filter time
constant
Winding/unwinding selection
Material thickness d1
Material thickness d2
Material thickness d3
Material thickness d4
Maximum winding diameter 1
Minimum winding diameter 1
Maximum winding diameter 2
Minimum winding diameter 2
Maximum winding diameter 3
Minimum winding diameter 3
Maximum winding diameter 4
Minimum winding diameter 4
Gear ratio numerator (follower side)
Gear ratio denominator (driver side)
Sampling time for winding diameter
calculation
Line speed at winding diameter calculated
value activation
Winding diameter change increment
amount limit
Winding diameter change limit disable
time
Number of averaging for winding diameter
calculation
Winding diameter compensation speed
filtering waiting time
Winding diameter compensation speed
filter time constant
Dancer lower limit position
Initial winding diameter calculation
deadband
Initial winding diameter calculation
deadband 2
Accumulated amount
Speed control P gain at start
Speed control integral time at start
Integral term limit at start
PID term limit at start
Winding length increment
Stored winding length
Winding length detection
Line multi-speed setting (high-speed)
Line multi-speed setting (middle-speed)
Line multi-speed setting (low-speed)
Line multi-speed setting (speed 4)
Line multi-speed setting (speed 5)
Line multi-speed setting (speed 6)
Setting range
1 to 3, 5 to 14, 17 to 20, 22 to 24,
26 to 36, 40 to 42, 46, 52 to 54, 61,
62, 64, 67, 81 to 91, 97, 98,
201 to 213, 230 to 232, 235 to 238
0, 1
0 to 2, 10
0, 1
1 to 9999 s
0 to 100%
0.1 to 10%
1, 8(0, 2, 3, 9, 12, 13, 90 to 96)
0 to 100%, 9999
0 to 10%
1 to 7
0 to 5 s
0, 1
0 to 20 mm, 9999
0 to 20 mm
0 to 20 mm
0 to 20 mm
1 to 6553 mm
1 to 6553 mm
1 to 6553 mm
1 to 6553 mm
1 to 6553 mm
1 to 6553 mm
1 to 6553 mm
1 to 6553 mm
1 to 65534
1 to 65534
0.01 to 1 s, 9999
0 to 6553.4
0 to 9.998 mm, 9999
0 to 100 s
0 to 10
0 to 100 s
0 to 100 s
400 to 600%
0 to 50%
0 to 50%, 9999
1 to 5000, 8888, 9999
0 to 1000%
0 to 20 s
0 to 100%
0 to 100%
0 to 3
0 to 9999
0 to 9999
0 to 6553.4
0 to 6553.4
0 to 6553.4
0 to 6553.4
0 to 6553.4
0 to 6553.4
Minimum
Initial
Customer
setting
value
setting
increment
201
202
203
204
1
205
206
207
208
1
0
1
0
1
0
1 s
50 s
0.1%
0%
0.1%
1%
1
0
0.1%
9999
0.1%
1%
1
2
0.01 s
0 s
1
0
0.001 mm
9999
0.001 mm
1 mm
0.001 mm
1 mm
0.001 mm
1 mm
1 mm
2 mm
1 mm
1 mm
1 mm
2 mm
1 mm
1 mm
1 mm
2 mm
1 mm
1 mm
1 mm
2 mm
1 mm
1 mm
1
1
1
1
0.01 s
9999
0.1
1
0.001 mm
9999
0.01 s
0 s
1
4
0.01 s
0 s
0.01 s
0 s
0.01%
400%
0.1%
1%
0.1%
9999
1
9999
1%
60%
0.001 s
2 s
0.1%
2.5%
0.1%
2.5%
1
3
1
0
1
1000
0.1
0
0.1
0
0.1
0
0.1
0
0.1
0
0.1
0
Advertisement
