Toro Greensmaster 3000 Series Operator's Manual
8 and 11 blade dpa reel mowers
Hide thumbs
Also See for Greensmaster 3000 Series:
- Installation instructions manual (20 pages) ,
- Setup instructions (2 pages) ,
- Operator's manual (16 pages)
Related Manuals for Toro Greensmaster 3000 Series
Summary of Contents for Toro Greensmaster 3000 Series
- Page 1 Form No. 3328–789 Rev. A 8 and 11 Blade DPA Reel Mowers Greensmaster 3000 Series Model No. 04610—Serial No. 230000001 and Up Model No. 04611—Serial No. 230000001 and Up Operator’s Manual English (EN, GB)
-
Page 2: Table Of Contents
Authorized Service precautions. Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 illustrates Warning signals a hazard that may cause serious injury or death if you do not follow the recommended precautions. -
Page 3: Specifications
Specifications General Specifications These cutting units will mount on the Greensmaster 3000, Greensmaster 3000–D, Tractors Greensmaster 3050, Greensmaster 3100, Greensmaster 3150, and Greensmaster 3250–D. Cutting height is adjusted on the front roller by two vertical screws and held by two Height of Cut locking capscrews. -
Page 4: Optional Equipment
Optional Equipment Powered Roller Brush for Model No. 04641 Greensmaster 3250 (Set of three) High Cut Bedknife Part No. 94–6392 Close Wiehle Scraper Kit Part No. 106–4661 Low Cut Bedknife Part No. 93–4264 (One scraper) Micro–Cut Bedknife Part No. 93–4262 Wide Wiehle Scraper Kit Part No. -
Page 5: Setup
Parts catalog Certificate of compliance Registration cards Fill out and return to Toro. 1. The cutting unit is shipped without a front roller. Install Chain link (Fig. 3) for Greensmaster 3250–D the roller using the loose parts supplied with the cutting traction unit. - Page 6 Important Whenever the cutting unit has to be tipped to expose bedknife/reel, prop up rear of cutting unit to make sure nuts on back end of bedbar adjusting screws are not resting on work surface (Fig. 4). Figure 6 1. Motor mount 3.
-
Page 7: Adjustments
(see Toro reel sharpening manual). 1. Position machine on a flat, level work surface. Make sure reel contact is removed by turning bedbar adjusting screws counterclockwise (Fig. -
Page 8: Adjusting The Height Of Cut
2. To adjust rear roller proceed as follows: Adjusting the Height of Cut Raise rear of cutting unit and place a block under Note: For heights of cut greater than .375“, the high height bedknife. of cut kit must be installed Remove (2) nuts securing each roller bracket and 1. -
Page 9: Adjusting The Cut-Off Bar
3. Hook screw head on cutting edge of bedknife and rest Adjusting the Cut-Off Bar rear end of bar on rear roller (Fig. 15). Adjust cut–off bar to assure clippings are cleanly discharged from the reel area: 1. Loosen screws securing top bar (Fig. 16) to cutting unit. Figure 15 4. -
Page 10: Operation
Operation Maintenance Note: Determine the left and right sides of the machine Note: Determine the left and right sides of the machine from the normal operating position. from the normal operating position. Cutting Unit Characteristics Servicing the Bedbar Removing the Bedbar The dual knob bedknife-to-reel adjustment system incorporated in this cutting unit simplifies the adjustment 1. -
Page 11: Backlapping The Reel
Note: Additional instructions and procedures on 2. Secure bedbar to each side plate with bedbar bolts (nuts Backlapping are available in the Toro Sharpening Reel & on bolts) and 8 washers. A nylon washer is to be Rotary Mowers Manual, Form No. 80-300PT. -
Page 12: The Toro General Commercial Products Warranty
If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.