Download Print this page
Sealey GSS1508G Instructions Manual
Sealey GSS1508G Instructions Manual

Sealey GSS1508G Instructions Manual

Galvanized steel shed green 1.5 x 0.8 x 1.9m
Hide thumbs Also See for GSS1508G:

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when building this shed.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Keep children and unauthorised persons away from the working area.
DO NOT use the shed for any purpose other than that for which it is designed.
Use appropriate safety clothing including eye protection.
NOTE: The assembly of this product will require assistance.
DO NOT attempt assembly in windy conditions
2.
INTRODUCTION
Galvanized, steel panels easily assembled to form a rigid and secure shed. Has skillion (sloping) roofs and single doors. Doors are secured by
cross bolt and eyelet which will accept a padlock (not included) for additional security. All models are supplied with bolt-down fixing kits.
3.
SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GSS1508G
Overall Size (W x D X H*): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1500 x 800 x 1900mm
Roof Type: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Skillion
*Minimum Wall Height.
4. CONCRETE SLAB
Concrete slab: Ensure that your site is level. It is recommended that your slab is 100mm thick and you use builders plastic and F52 reinforcing
mesh. We recommend that you make your slab 100mm bigger than the base dimensions of your shed. This will allow for a 50mm edge around your
shed. We recommend that you slope the 50mm edges downward by 10 mm so that rain water can be drained away from your shed.
© Jack Sealey Limited
INSTRUCTIONS FOR:
GALVANIZED STEEL SHED GREEN
1.5 x 0.8 x 1.9m
GSS1508G
MODEL NO:
Original Language Version
GSS1508G
Issue: 1 - 28/08/14

Advertisement

loading

Summary of Contents for Sealey GSS1508G

  • Page 1 GSS1508G MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2: Tools Required

    Sheet 1980x770 -right Sheet Sheet 1900-1980x770 -left side wall Sheet Sheet 1900-1980x770 -right side wall Sheet Sheet 855x770 roof Sheet 1900x708 front Door Sheet 1845x770 door Original Language Version © Jack Sealey Limited GSS1508G Issue: 1 - 28/08/14...
  • Page 3 Self tapper safety cover (L type) Channel safety cover (R type) Rawlbolt In the unlikely event that you find you are missing a part, please contact your Sealey dealer. Original Language Version © Jack Sealey Limited GSS1508G Issue: 1 - 28/08/14...
  • Page 4: Parts Diagram

    You will find it easier to assemble your shed using saw horses with timber battens attached (the timber needs to be the same length as the shed (1.5m). Alternatively, a trestle table can be used. Original Language Version © Jack Sealey Limited GSS1508G Issue: 1 - 28/08/14...
  • Page 5 Now fit 20B top channel and 20C bottom channel to the sheeting by tapping it in (diagram A) or sliding it in (diagram B). Note that the small lip of the channel is always facing out. This is to ensure that rain water can not build up inside the shed. Original Language Version © Jack Sealey Limited GSS1508G Issue: 1 - 28/08/14...
  • Page 6 Note that the small lip of the channel is always facing out. This is to ensure that rain water can not build up inside your shed. Repeat the same steps for 2L the other side wall. Original Language Version © Jack Sealey Limited GSS1508G Issue: 1 - 28/08/14...
  • Page 7 Now tap or slide in 20A and 20A the channels to the sheeting and fix them using the self tapping screws. 8.3.3. Now tap or slide in 20A and 20A the channels to the sheeting and fix them using the self tapping screws. Original Language Version © Jack Sealey Limited GSS1508G Issue: 1 - 28/08/14...
  • Page 8 Fit the 41A the jamb, 42 the jamb and 23 the bottom channel and fix them using the self tapping screws (NOT those with cross mark in this stage). Be aware of the joint details per the diagrams. (DIAGRAM B IS AS THE SAME AS DIAGRAM A.) Original Language Version © Jack Sealey Limited GSS1508G Issue: 1 - 28/08/14...
  • Page 9 Fit 5R the pre-assembled door to the front wall panel per the diagram. Use riveter to fix the door into the pre-drilled holes. Fix the pad bolt (but NOT its keeper in this stage) to the pre-drilled holes using supplied rivets or self tapping screws. Original Language Version © Jack Sealey Limited GSS1508G Issue: 1 - 28/08/14...
  • Page 10 Fit 5R the pre-assembled door to the front wall panel per the diagram. Use riveter to fix the door into the pre-drilled holes. Fix the pad bolt (but NOT its keeper in this stage) to the pre-drilled holes using supplied rivets or self tapping screws. Original Language Version © Jack Sealey Limited GSS1508G Issue: 1 - 28/08/14...
  • Page 11 Now fit the bolt down kit using the supplied masonry bolts as per the diagram. Strengthen your mid wall brace by applying 72 the mid wall brace bracket on each corner if necessary. MASONRY BOLT Original Language Version © Jack Sealey Limited GSS1508G Issue: 1 - 28/08/14...
  • Page 12 Sealey sheds are weatherproof; however, heavy winds with driving rain could cause your shed to leak. Condensation will also occur in some weather conditions such as extreme heat or cold. We would recommend the use of a waterproof sealant to help seal around all joins and wherever you feel that water may get in under these extreme conditions.
  • Page 13 Fill the old pre-drilled holes with rivets if required. Perform the same procedure for the pad lock. Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.