Sealey SA6002.V4 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
WARNING! DO NOT use wrench if damaged or thought to be faulty. Contact Service Agent.
‰
WARNING! Disconnect from the air supply before changing accessories or servicing.
‰
WARNING! Due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we
‰
recommend you wear suitable respiratory protection.
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
‰
DO NOT use the wrench for a task it is not designed to perform.
8
DO NOT use worn, or damaged sockets
8
DO NOT use the wrench unless you have been instructed in its use by a qualified person.
8
DO NOT carry the wrench by the air hose.
8
DO NOT operate the wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT carry the wrench with your hand on the power trigger in order to avoid unintentional starting.
8
DO NOT direct air from the air hose at yourself or others.
8
DO NOT expose air tools to rain. Do not use air tools in damp or wet locations.
8
Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
Only use impact sockets which are specifically designed for use with an impact wrench.
9
Wear approved safety eye/face shield, ear defenders, dust mask and hand protection.
9
Follow all workshop safety rules, regulations, and conditions when using the wrench.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Operate with both hands when practical to do so.
9
Keep children and non essential persons away from the working area.
9
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
‰
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
2. INTRODUCTION
Composite body with aluminium front casing for light weight and
durability. One hand operation with three speed selector switch
and forward/reverse control at your fingertips. Handle features a
downward facing exhaust to lower noise level and soft grips to help
reduce vibration and chill. Suitable for professional garages.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . .SA6002.V4
Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . . 5.4cfm
Breakawy Torque:. . . . . . . . . . . . . . . 1400lb.ft(1900Nm)
Drive: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/2"Sq
Free Speed: . . . . . . . . . . . . . . . . . . . . . . . . . . 7300rpm
Inlet Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BSP
Maximum Torque: . . . . . . . . . . . . . . . . 800lb.ft(1085Nm)
Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . . .111dB(A)
Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . . 100dB(A)
Operating Pressure: . . . . . . . . . . . . . . . . . . . . . . . .90psi
Vibration: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.922m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.77m/s²
4. PREPARATION
© Jack Sealey Limited
AIR IMPACT WRENCH
1/2"SQ DRIVE TWIN HAMMER
MODEL NO:
Wear protective Wear ear
gloves protection
Original Language Version
SA6002.V4
Wear a mask
SA6002.V4 | Issue 1 10/07/2019