Keyboard Hookup; Satellite Configuration Installations - Philips Allegiant LTC 8500 Series Instructions For Use Manual

If a TC8802 monitor expansion bay is supplied, each
camera that is connected to the TC8801 main CPU
bay must also be connected to the same numbered
input on the monitor expansion bay.
TC8802 Video Connections
With the TC8802 monitor expansion bay, ribbon
cable connectors are provided for the video inputs.
Video is to be looped from the main bay into the
expansion bay through 16 TC8809 ribbon cables.
Connect all TC8809 ribbon cables from the
appropriate "VIDEO" ribbon cable connector on the
main bay to the corresponding "VIDEO" ribbon cable
connector on the monitor expansion bay. The ribbon
cable connectors contain
protrusion formed into one side of the connector
to assure proper placement into the mating
connectors. Be careful not to force the cables
into the mating connectors backwards. The DIP
switches on the VIM cards installed in the main bay
should be turned OFF. This will make the main bay
inputs non-terminated, and the expansion bay will
provide the termination for the video inputs.
VIDEO
VIDEO IN
KEYBOARD
OUT
CONSOLE
7 6
INPUT 161-176 8 5 LOOP 1-16
1 2 13 1
ALARM
LOOP 161-176 16 15 14 LOOP 17-32
13
14 2
3 4
PRINTER
INPUT 177-192 LOOP 33-48
24 23 22 21
15 3
5 6 LOOP 177-192 LOOP 49-64
SDA
32 31 30 29
16 4
INPUT 193-208 LOOP 65-80
7 8 40 39 38
COMM PORT 1 37
17 5
LOOP 193-208 LOOP 81-96
48 47 46 45
32 25 18 6 INPUT 209-224 INPUT 97-112
COMM PORT 2
56 55 54 53
LOOP 209-224 LOOP 97-112
26
SYNC 19 7
IN
64 63 62 61
INPUT 225-240 INPUT 113-128
27
20 8
LOOP 225-240 70 LOOP 113-128
72 71 69
28 21 9
INPUT 241-256 INPUT 129-144
80 79 78 77
29 22 10
LOOP 241-256 LOOP 129-144
88 87 86
85
30 23 11
INPUT 145-160
96 95 94 93
TC8801
31 24 12 LOOP 145-160
VIDEO
VIDEO IN
KEYBOARD
OUT
CONSOLE
6
8 7 5
INPUT 161-176 LOOP 1-16
1 2 13 1
LOOP 161-176 16 15 14 13 LOOP 17-32
14 2
3 4
INPUT 177-192 LOOP 33-48
24 23 22 21
15 3
5 6 LOOP 177-192 LOOP 49-64
32 31 30 29
16 4
INPUT 193-208 LOOP 65-80
7 8 40 39 38 37
17 5 LOOP 193-208 LOOP 81-96
48 47 46 45
32 25 18 6 INPUT 209-224 INPUT 97-112
COMM PORT 2
54
56 55 53
LOOP 209-224 LOOP 97-112
SYNC 26 19 7
IN
63 62
INPUT 225-240 64 61 INPUT 113-128
27
20 8
LOOP 225-240 LOOP 113-128
72 71 70 69
28 21 9
INPUT 241-256 INPUT 129-144
80 79 78 77
29 22 10
LOOP 241-256 LOOP 129-144
88 87 86 85
30 23 11
INPUT 145-160
96 95 94 93
TC8802
31 24 12 LOOP 145-160
Typical TC8809 Connections
TC8802 Data Connections
The TC8802 is supplied with a TC8716C2 data
communication interconnect
connectors spaced about 3 feet apart. Install the
TC8716C2 cable between the Comm1 port on the
TC8801 Main CPU bay, and the Comm1 port on the
TC8802 monitor expansion bay.
a small "key"
3 2
4 1
12 11 10
9
20 19 18 17
28 27 26 25
36 35 34
33
44 43 42 41
52 51 50 49
60 59 58 57
66
68 67 65
76 75 74 73
84 83 82
81
92 91 90 89
TC8809
2
4 3 1
Ribbon
12 11 10 9
Cables
20 19 18 17
28 27 26 25
36 35 34 33
44 43 42 41
50
52 51 49
58
60 59 57
68 67 66 65
76 75 74 73
84 83 82 81
92 91 90 89
cable with two

Keyboard Hookup

Connect a maximum of 8 system keyboards to any
of the 8 keyboard ports (modular phone type jacks)
provided on the rear of the TC8x01 Main CPU bay,
but be sure to at least connect a keyboard to port #1.
The TC8500 is limited to these 8 keyboards. Other
systems may accommodate 16 or 32 keyboards
using TC8714A and TC8715A series keyboard port
expander accessory units.
Additional keyboards may also be used with a
TC8802A Series Monitor Expansion Bay. Connect
the keyboards the same way as with the TC8801A
Series Main Bay. DIP switches 2 and 3 of S101 on
the Data Receiver module in the Monitor Expansion
Bay must now be set according to the table below.
Desired Keyboard Numbers
On Monitor Expansion Bay
Keyboards Switch 2
None OFF
9 to 16 OFF
17 to 24 ON
25 to 32 ON
Each keyboard is supplied with a 10-foot cable for
local hookups. The TC8x01 can provide power to
keyboards up to 100 feet away using the optional
TC8557HL hookup cable. For distances of up to
5000 feet, the optional TC8557HR hookup kit is
required, which is supplied with a remote power pack
and requires user-supplied shielded twisted pair
(Belden 9841 or equivalent) for communication.

Satellite Configuration Installations

Due to the many variations possible, only general
guidelines can be covered for installing satellite
systems. Refer to the appendix section of this
manual, the TC8850 Graphical User Interface
Software manual or the TC8x59 Master Control
Software package
configuration and programming information on
satellite systems.
Video and
Data Links
Satellite
System
#1
Satellite
System
#2
Satellite Concept Configuration
23
Switch 3
OFF
ON (recommended setting)
OFF
ON
manual for additional
Central
Control
Station
Satellite
System
#6
Satellite
System
#3
Satellite
System
#5
Satellite
System
#4
S9507002AE