Sealey PSB05 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instructions protection
1. safety
Warning! turn off, or disconnect from air supply before servicing or performing any maintenance and when unit is not in use.
‰
Warning! this sand blasting gun will generate gritty dust which could damage surface finishes and contaminate moving parts. it
‰
is recommended that sand blasting be carried out in a dedicated room free from unrelated materials and where there is adequate
lighting. Where this is not possible consideration should be given to covering exposed surfaces and masking moving parts as necessary.
Warning! Wear approved ear, eye, hand and respiratory protection when operating the blaster. A full range of personal safety
‰
equipment is available from your sealey stockist.
maintain correct balance and ensure firm footing by wearing non slip shoes.
9
spillages of abrasive material, which may be slippery, must be cleaned up immediately to avoid injury.
9
maintain the blaster in good condition (use an authorised service agent).
9
replace or repair damaged parts. use recommended parts only. unauthorised parts may be dangerous and will invalidate the warranty.
9
Keep the unit clean for best and safest performance.
9
remove ill fitting clothing. remove ties, watches, rings, and other loose jewellery and contain long hair.
9
Always keep the blast nozzle directed at the work piece.
9
if a failure or malfunction occurs immediately disconnect from air supply.
9
Keep all other persons away from the working area. contact with high pressure blast or inhaling the dust generated is dangerous. if
9
other personnel are required in the vicinity of the sand blasting then they must wear protective equipment similar to the operator's.
do not use the blaster for any purpose other than that for which it is designed.
8
do not attempt to clear a blocked nozzle while the unit is pressurised.
8
do not allow untrained persons to operate the blaster.
8
do not leave the blaster operating unattended.
8
do not stand on the blaster.
8
do not direct air from the air hose at yourself or others.
8
do not operate system with air supply exceeding 115 psi.
8
do not operate the blaster if any parts are missing or damaged as this may cause failure and/or personal injury.
8
do not get the blaster wet or use in damp or wet locations or areas where there is condensation.
8
do not operate the blaster when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
do not use any abrasive which contains free silica, as indicated in the Health & safety Guidance note eH59 (available from Hmso).
8
note: this appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or
lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a
person responsible for their safety. children should be supervised to ensure that they do not play with the appliance.
2. introdUction
suitable for controlled removal of paint, mould, carbon, grease and rust. When adjusted correctly, is particularly useful in areas where less
aggressive cleaning is required, such as around windows (without etching the glass) and even for stripping paint from wooden furniture.
suitable for use on food industry machinery, as soda-blasting is an A1 rated cleaning agent. Also inhibits rust on untreated surfaces for up to
six weeks. made of strong composite resin. Just add dry soda blasting media into the container and connect to source of compressed air to
use. Adjustable nozzle allows control from narrow to wider stream.
3. specification
model no. .................................................................... PsB05
nozzle dia. ..................................................................... 5mm
operating Pressure .................................................75-115psi
Air consumption.............................................. 8.5cfm@90psi
Abrasives:- We recommend the use of sealey blasting soda sBG25Kg
© Jack sealey limited
instructions for
portable soda blasting gUn
model no:
Wear protective Wear safety
gloves footwear
Original Language Version
psb05
Wear protective Wear a mask
clothing
fig.1
PsB05 | issue 1 25/01/18