Related Manuals for Mitsubishi Electric MP-G10-AO
Summary of Contents for Mitsubishi Electric MP-G10-AO
- Page 1 INDUSTRIAL SEWING MACHINE Attachment MODEL MP-G10-AO TECHNICAL MANUAL Pneumatic Type Clamp A180E627P03...
-
Page 2: For Safe Use
FOR SAFE USE Before the installation, operation, and inspection for this product, read the “FOR SAFE USE” and the technical manuals carefully. Also read the other technical manuals, “Sewing Machine Head”, “Control Unit” and “Operation Panel” describing some instructions, which are not in this manual, and use the sewing machine properly. -
Page 3: Specifications
This clamp is effective if the material to be stitched is heavy and the magnetic type clamp is too weak to hold the material, or if the material is soft and needs to be gently pressed. 2. Specifications ： MP-G10-AO (pneumatic type clamp) Name ： PLK-G1010 Applicable model: ：... - Page 4 3. Configuration ★ The Fig. numbers in the drawing correspond to the part numbers given in the following explanations. 3.1 Clamp mechanism - 2 -...
- Page 5 3.1 Clamp mechanism (Parts list) 部品コード 数量 品 名 Description Parts No. Amt. Req. M91055020 ﾛｯｶｸｱﾅﾂｷﾄﾒﾈｼﾞ M4X4 Screw M4X4 MH10A0352 ｶﾗｰ Collar M90519050 ﾅｲﾛﾝﾜｯｼｬ Nylon washer M91109002 ﾋﾗﾈｼﾞ 11/64(40)X7 Screw 11/64(40)X7 M90421050 ｻﾞｶﾞﾈ 4 Washer 4 MH10K0950 ﾚﾊﾞｰ(S2L) Lever (S2L) MH10K1950 ﾚﾊﾞｰ(S1) Lever (S1) M90538060 ﾅｯｸﾙﾋﾟﾝ(L)
- Page 6 3.2 Pneumatic pressure control unit 3.3 Accessories - 4 -...
- Page 7 3.2 Pneumatic pressure control unit (Parts list) 部品コード 数量 品 名 Description Parts No. Amt. Req. MH25A1601 ﾃﾞﾝｼﾞﾍﾞﾝﾄﾘﾂｹｲﾀ Valve mounting plate M91066004 SW-PW ﾌﾟﾗﾏｲﾅﾍﾞﾈｼﾞ M4X25 Screw M4X25 ME10X0599 ﾃﾞﾝｼﾞﾍﾞﾝｸﾐﾀﾃ Solenoid valve assy M90511050 ｻﾞｶﾞﾈ 5 Washer 5 M95003017 ｾﾌﾃｨｿｹｯﾄ M5X8 Safety socket bolt M5X8 MB10B0508 ｾﾂｿﾞｸﾃﾞﾝｾﾝｸﾐﾀﾃ...
-
Page 8: Setup Procedures
4. Setup procedures CAUTION Alwa ys mak e sure that the powe r is OFF before sta rting se ttin g wo rk . 4.1 Installing the clamp drive mechanism (1) Remove the four screws on the Y axis movement race side fixing the clamp base (Fig.No.112) and the two screws on the axis support side, and remove the magnetic clamp mechanism mounted as a standard on the sewing machine. -
Page 9: Installing The System Software
Signal name Connection Solenoid Sewing machine head solenoid PCB valve White +24V CON13 (FU) - ② Work holder ouput 1 Sewing machine head solenoid PCB Black CON13 (FU) - ① ( O4 ) 4.4 Installing the system software When this sewing machine is already used, installation explained by this 4.4 clause is not necessary. - Page 10 (4) Enter a password Please ask the dealer about a password. (5) Press the inside of the frame under the (A display in the frame is OF1 in a standard setting. If it is the other display, change to OF1.) * Refer to the clause Output confirmation (Custom output) [of 2.Explanation of input/output setting mode of [14]Input/output setting mode] of the technical manual ”Operation Panel”...
-
Page 11: Operation
5. Operation 5.1 Confirming operation (1) Turn the sewing machine power switch ON. (2) Confirm that the work clamp lower when the foot switch (2-pedal) [Black] side is turned ON, and rise when the switch is turned ON again. (3) Lower the work clamp, and press on the operation panel. - Page 12 Printed in Japan...