Related Manuals for Mitsubishi Electric MP-G10-EX
Summary of Contents for Mitsubishi Electric MP-G10-EX
- Page 1 INDUSTRIAL SEWING MACHINE Attachment MODEL MP-G10-EX TECHNICAL MANUAL Extension Kit A180E610P03...
-
Page 2: For Safe Use
FOR SAFE USE Before the installation, operation, and inspection for this product, read the “FOR SAFE USE” and the technical manuals carefully. Also read the other technical manuals, “Sewing Machine Head”, “Control Unit” and “Operation Panel” describing some instructions, which are not in this manual, and use the sewing machine properly. -
Page 3: Specifications
2. Specifications ： MP-G10-EX (Extension Kit) Name ： PLK-G1010 Applicable model: ：... - Page 4 3. Configuration ★ The Fig. numbers in the drawing correspond to the part numbers given in the following explanations. 3.1 Clamp mechanism - 2 -...
- Page 5 3.1 Clamp mechanism (Parts list) 部品コード 数量 品 名 Description Parts No. Amt. Req. M91055020 ﾛｯｶｸｱﾅﾂｷﾄﾒﾈｼﾞ M4X4 Screw M4X4 MH10A0352 ｶﾗｰ Collar M90519050 ﾅｲﾛﾝﾜｯｼｬ Nylon washer M91109002 ﾋﾗﾈｼﾞ 11/64(40)X7 Screw 11/64(40)X7 M90421050 ｻﾞｶﾞﾈ 4 Washer 4 MH10K0950 ﾚﾊﾞｰ(S2L) Lever (S2L) MH10K1950 ﾚﾊﾞｰ(S1) Lever (S1)
- Page 6 3.2 X-Y Table mechanism 3.3 Pneumatic pressure control unit - 4 -...
- Page 7 3.2 X-Y Table mechanism (Parts list) 部品コード 数量 品 名 Description Parts No. Amt. Req. MH10X2339 X ｲﾄﾞｳｶﾊﾞｰ(L) Movable cover X (left) MH10X0407 ｹﾝｼｭﾂﾊﾞﾝ X Detector plate X MH10X3339 X ｲﾄﾞｳｶﾊﾞｰ(R) Movable cover X (right) M90990002 ﾋﾗﾈｼﾞ M4X8 Screw M4X8 MH10A1476 ﾍﾞﾙﾄｽﾍﾟｰｻ...
-
Page 8: Accessories (Parts List)
3.4 Accessories 3.4 Accessories (Parts list) 部品コード 数量 品 名 Description Parts No. Amt. Req. MF06A1620 ｹｯｿｸﾊﾞﾝﾄﾞ Cable tie M94007099 ﾅｲﾛﾝｸﾘｯﾌﾟ 6 Nylon clip 6 M91054004 SW-PW ﾌﾟﾗﾏｲﾅﾍﾞﾈｼﾞ M4X8 Screw M4X8 MB60A1620 ﾅｲﾛﾝｸﾘｯﾌﾟ 8 Nylon clip 8 M90409041 ﾏﾙﾓｸﾈｼﾞ 4.5X20 Screw 4.5X20 MH10X0691 ﾊﾟｯｷﾝｾｯﾄ... -
Page 9: Setup Procedures
4. Setup procedures CAUTION Alwa ys mak e sure that the powe r is OFF before sta rting se ttin g wo rk . 4.1 Installing the clamp mechanism and X axis table mechanism (1) Remove the shaft (Fig.No.120) from the shaft holder (Fig.No.119) by loosening the set screw for the shaft holder coupling the Y drive shaft and clamp. - Page 10 4.2 Installing the slide plate (1) Refer to the part catalog P-246 for the PLK-G1010 sewing unit, and remove Fig No.B125 slide plate (outside), Fig.No.B118, B119, B120, and B129. (2) Temporary fix the enclosed Fig.No.142, 145, slide plate brackets L/R and Fig.No.143 mounting plate with the bolts Fig.No.144, 146, and etc., onto the sewing machine bed.
- Page 11 (3) When installing the detector at the positon A, place it to the oposite direction to avoid stressing the detector code. (4) Refer to the PLK-G1010 Sewing Machine Head version instruction manual (7-21. Adjustment of the X-Y mechanical home position), and adjust the home position. CAUTION ・The clamp mechanism and wiper could interfere depending on the home position.
-
Page 12: Installing The System Software
4.6 Installing the system software CAUTION If the sewing machine is operated with the magnetic clamp settings, faults could occur. Always install the system software for the extension kit. (1) Installing the System Software ① While holding down the [F] key on the front panel of the control box, turn the machine power ON. (Keep pushing [F] key until red LED on the front panel is turned on.) ②... -
Page 13: Confirming Operation
5. Operation 5.1 Confirming operation (1) Turn the sewing machine power switch ON. (2) Confirm that the clamp lowers when the foot switch (2-pedal) [Black] side is turned ON, and rises when the switch is turned ON again. If the operation is reversed, check whether the piping connection is incorrect. - Page 14 MEMO...
- Page 15 MEMO...
- Page 16 Printed in Japan...