ABB PVI-3.0-TL-OUT Quick Installation Manual

ABB Solar inverters
Quick Installation Guide
PVI-3.0/3.6/4.2-TL-OUTD
EN
In addition to what is explained below, the safety and installation information provided in the
installation manual must be read and followed. The technical documentation and the interface
and management software for the product are available at the website.
The device must be used in the manner described in the manual. If this is not the case the
safety devices guaranteed by the inverter might be ineffective.
3.
Available components
Bracket for wall mounting
Bolts and screws for wall mounting
M6x10 screw
D.18 Washer
L-key, TORX TX20
M20 Cable gland
M25 Cable gland
4.
Transport and handling
components from violent shocks, humidity, vibration, etc.
Lifting
Unpacking and checking
The components of the packaging must be disposed on in accordance with the regulations in force in the country of
installation.
Equipment weight
Model
PVI-3.0-TL-OUTD PVI-3.6-TL-OUTD PVI-4.2-TL-OUTD
PVI-3.0-TL-OUTD-S PVI-3.6-TL-OUTD-S PVI-4.2-TL-OUTD-S
5.
Environmental checks
- Consult the technical data to check the environmental parameters to be observed
- Installation of the unit in a location exposed to direct sunlight must be avoided as it may cause:
1. power limitation phenomena in the inverter (with a resulting decreased energy production by the system)
2. premature wear of the electrical/electromechanical components
3. premature wear of the mechanical components (gaskets) and of the user interface (display)
- Do not install in small closed rooms where air cannot circulate freely
-
-
- Do not install in rooms where people live or where the prolonged presence of people or animals is expected,
because of the noise (about 50dB(A) at 1 m) that the inverter makes during operation
Installations above 2000 metres
-
temperatures
- Reduction in the dielectric resistance of the air that, in the presence of high operating voltages (DC input), can
create electric arcs (discharges) that can reach the point of damaging the inverter
All installations at altitudes of over 2000 metres must be assessed case by case with the ABB Service
department.
Quantity Available components
Two-hole gasket for M20 signal cable
glands and cap TGM58
1
parallel input channels
Connector for the connection of the
communication and control signals
2 + 2
1
3
ABB ABB
1 XXXXX XXXXX solar solar inverters XXXXX XXXXX inverters
XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX
XXXXX XXXXX XXXX XXXX XXXX XXXX
Technical documentations
The technical technical The In addition In addition to what to what is explained documentatio documentatio is explained
n and n and guide, in this the interface in this interfa the guide, f ce the the f y safety safet
1 management management and and installation and installation and w t are soft f software information info f f rmation
for the fo f f r the product provided provided product are in the available are in the available installation installation
at the at the manual website. manual website. mus t s s be mus read read t be and and
fo f f llowed. followed.
1
Mass weight
17.5 Kg
1.
www.abb.com/solar
SOLAR INVERTER
V dc max 600 V
V dc MPP 90 - 580 V
V 160 - 530 V
dc, Full Power
I 2 x 10 A
dc max
I 2 x 12.5 A
sc max
IP65
-25 to +60 °C
-13 to +140 °F
The labels attached to the equipment must NOT be removed, damaged, dirtied, hidden,etc...
Always refer to instruction
manual
Protection rating of
IP65
Positive pole and negative
pole of the input voltage
(DC)
2.
The models of inverter to which this guide refers are available in 3 power ratings: 3.0 kW, 3.6 kW and 4.2 kW.
The only difference in terms of components between the three power levels is the number of input connectors: 2 pairs in PVI-3.0/3.6-TL-OUTD models; 3 (2x MPPT1
and 1x MPPT2) pairs in PVI-4.2-TL-OUTD models. Two types are available for each model: Standard or with DC disconnect switch (Version -S).
03
POW
ER
05 06
Main components
01 Bracket
Locking screw
02
03 Heat sink
DSP Reprogramming
04
connectors
Quantity
1 + 1
2
15
2
cm
2 (3.0/3.6 kW)
3 (4.2 kW)
10cm 10cm
2 (3.0/3.6 kW)
3 (4.2 kW)
20
cm
1
6.
Position the bracket so that it is perfectly level on the wall and use it as a boring template.
01
70 mm. On the bracket 01 there are 5 holes with which to secure it: just 2 are enough to support the inverter if
installed on stable, robust supports.
Secure the bracket to the wall
Hook the inverter to the bracket spring corresponding with the insertion point in the bracket on the back of
the inverter (Step 2).
Proceed to anchor the inverter to the bracket
side (Step 3).
POWE R
ALAR
M
GFI
Unscrew the 4 screws and open the front cover
ESC
UP
DOWN
ENTER
U N O
Once the connections have been made, close the cover by tightening the 4 screws on the front to a
7.
which can however be connected in parallel using a single MPPT.
independent mode.
This means that the jumpers between the two channels (positive and negative)
of the DC input terminal block
located on the main board must be set to "IND".
of the DC input terminal block
DIN V VDE 0126-1-1
DIN V VDE 0126-1-1
PROTECTIVE CLASS: I
PROTECTIVE CLASS: I
Made in Italy
www.abb.com/solar
MODEL: MODEL:
PVI-3.0-TL-OUTD SOLAR INVERTER PVI-3.6-TL-OUTD
V acr 230 V 1Ø V dc max 600 V V acr 230 V 1Ø
V 90 - 580 V f 50 Hz
f r 50 Hz dc MPP r
P 3000 W @ 50°C amb. V 120 - 530 V P 3600 W @ 55°C amb.
acr (cos = 1) dc, Full Power acr (cos = 1)
P 3000W @ 45°C amb. I 2 x 16 A P 3600W @ 50°C amb.
acr (cos = ±0.9) dc max acr (cos = ±0.9)
I 14.5 A I 2 x 20 A I 17.2 A(*)
ac max sc max ac max
(*): 16 A for UK G83 Version
IP65
-25 to +60 °C
5 minutes
-13 to +140 °F
01
PVI-X.X-TL-OUTD-Y
Inverter model
01
02
Inverter Part Number
02
P/N:PPPPPPPPPPP
Inverter Serial Number
04 03
SN:YYWWSSSSSS WK:WWYY
Week/Year of manufacture
04
03
WO:XXXXXXX
SO:SXXXXXXXX Q1
General warning - Important
safety information
Without isolation
Temperature range
transformer
Always use safety clothing
Point of connection for
and/or personal safety
grounding protection
devices
01
04
02
ALA
RM
GFI
ESC
UP
DOW
N
ENT ER
U N O
07 08
16
05 Front cover 09 DC Input terminal block 13
LED Panel AC Output terminal block
06 10 14
07 Display 11 15
08 Keyboard 12 Internal battery 16
Installation position
-
- Install in safe, easy to reach places
- If possible, install at eye-level so that the display and status LEDs can be seen easily
-
- Install vertically with a maximum inclination of +/- 5°
- Choose a place with enough space around the unit to permit easy installation and
removal of the object from the mounting surfaces; comply with the indicated minimum
distances
- For a multiple installation, position the inverters side by side; if the space available does
not allow this arrangement, position the inverters in a staggered arrangement as shown
Final installation of the inverter must not compromise access to any disconnection
devices that may be located externally.
Please refer to the warranty terms and conditions available on the website and
evaluate any possible exclusion due to improper installation.
B or to the pole A with the no. 2 10 mm wall plugs supplied with it (Step
by tightening the locking screw located on the lower
01 02
in order to make all the necessary connections.
05
09 must not be installed and the switch 11
must be installed and the switch located on the main board must be set to "PAR".
09 11
09
DIN V VDE 0126-1-1
PROTECTIVE CLASS: I
Made in Italy Made in Italy
www.abb.com/solar
MODEL:
SOLAR INVERTER PVI-4.2-TL-OUTD
V dc max 600 V V acr 230 V 1Ø
V 90 - 580 V f 50 Hz
dc MPP r
V 140 - 530 V P 4200 W @ 50°C amb.
dc, Full Power acr (cos = 1)
I 2 x 16 A P 4200W @ 45°C amb.
dc max acr (cos = ±0.9)
I 2 x 20 A I 20 A
sc max ac max
IP65
-25 to +60 °C
5 minutes 5 minutes
-13 to +140 °F
Hot surfaces
Direct and alternating
currents, respectively
Time need to discharge
stored energy
10
09 10 11 12 13 14 15
17 18 19 20
09 10 11 12 13 14 15
17 18 19 20
Signal terminal block 17 Input connectors (MPPT1)
RJ45 Connectors Input connectors (MPPT2)
18
RS485 line termination switch 19 AC cable gland
DC Disconnect switch 20 Service cable glands
1
2
POWER
ALARM
GFI
ESC
UP DOWN ENTER
A
UNO
B
3
11
11