Table of Contents
Advertisement
listening through a receiver
You can listen to sound through a receiver instead of the tV speaker.
1. Press the toolS button. Then Press the enter
CEC)".
Press the ▲ or ▼ button to select "Receiver", then press the enter
. Press the ◄ or ► button to select to "On", then press the enter
Now you can listen to sound through the receiver.
. Press the eXIt button to exit.
➣
When the receiver is set to On, you can listen to the TV sound through the 2-channel
receiver.
➣
If the receiver is exclusively for a home theatre only (supporting audio only), it may not
appear in the device list.
➣
Only when you have connected the optical jack of the TV and the receiver properly, does Receiver work.
➣
In case of a content with copyright problem, listening through the receiver may not properly operate.
➣
If there is a power interruption to the TV when the "Receiver" is set to "On" (by disconnecting the power cord or a power
failure), the "TV Speaker" may be set to "Off" when you turn the TV on again. (see page 21)
Check Points before requesting Service
Symptom
anynet+ does not work.
I want to start anynet+.
I want to exit anynet+.
the Configuring anynet+
connection message appears
on the screen.
the anynet+ device does
not play.
the connected device is not
displayed.
the tV programme cannot be
recorded.
the tV sound is not output
through the receiver.
button to select "Anynet+(HDMI-
Solution
■
Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
■
Connect only one receiver.
■
Check if the Anynet+ device power cord is properly connected.
■
Check the Anynet+ device's Video/Audio/HDMI 1.3 cable connections.
■
Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■
Check whether the TV remote control is in TV mode.
■
Check whether it is Anynet+ exclusive remote control.
■
Anynet+ doesn't work at a certain condition. (Searching channels, Operating WISELINK, Plug & Play,
etc.)
■
When connecting or removing the HDMI 1.3 cable, please make sure to search devices again or
restart your TV.
■
Check if the Anynet+ Function of Anynet+ device is set on.
■
Check if the Anynet+ device is properly connected to the TV and check if the Anynet+ (HDMI-CEC) is
set to On in the Anynet+ Setup menu.
■
Press the tV/DtV button on the TV remote control to switch to TV. Then press the toolS button to
show the Anynet+ menu and select a menu you want.
■
Select View tV in Anynet+ menu.
■
Press the SourCe button on the TV remote control and select a device other than Anynet+ devices.
P
/
■
Press any of
and Pre-Ch such to change to the TV mode. (Note that the channel button
operates only when a tuner-embedded Anynet+ device is not connected.)
■
You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
■
Use the remote control when the Anynet+ setting or switching to view mode is complete.
You cannot use the play function when Plug & Play is in progress.
■
Check whether or not the device supports Anynet+ functions.
■
Check whether or not the HDMI 1.3 cable is properly connected.
■
Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
■
Search Anynet+ devices again.
■
You can connect an Anynet+ device using the HDMI 1.3 cable only. Some HDMI cables may not
support Anynet+ functions.
■
If it is terminated by an abnormal situation such as disconnecting the HDMI 1.3 cable or power cord
or a power failure, please repeat the device scan.
Check whether the antenna jack on the recording device is properly connected.
Connect the optical cable between TV and the receiver.
button.
button.
english -
tV
P
View tV
Select Device
record
menu on Device
Device operation
receiver
:off
Setup
move
enter
return
Advertisement
Table of Contents
