Related Manuals for Aqualisa AQ75
Summary of Contents for Aqualisa AQ75
- Page 1 AQ100 AQ75:Midas 8/9/15 13:53 Page 1 AQ75 AQ100 3245F Thermostatic bar mixer valve with adjustable head Installation guide...
-
Page 2: Table Of Contents
- Stored water capacities Balanced high pressure systems Combination boiler systems Typical water systems System components Bar valve installation p.10 AQ75 adjustable height head installation p.11 AQ100 adjustable height head installation p.13 3245F adjustable height head installation p.14 Handset to hose installation p.15... -
Page 3: Introduction
If in any doubt, please contact the appliance manufacturer before installation commences. Connections The Aqualisa bar valve product is designed for conventional supplies with HOT on the Left and COLD on the Right as viewed from the front. Supply lines must be flushed clear of any debris before installation of the unit. Any debris accumulation in the... -
Page 4: Flushing
Pressures The Aqualisa bar valve is designed to control static pressure up to 10 bar. Where pressures are likely to exceed 5 bar, a pressure reducing valve (PRV) must be fitted into the incoming mains supply. A setting of 3 bar is recommended. It should be noted that daytime pressures approaching 8 bar can rise above the stated maximum overnight. -
Page 5: Pump Installation
A pump must only be used to boost the pressure from tank-fed supplies. A typical layout is shown on page 6. A minimum 1.5 bar twin ended booster pump may be fitted with the Aqualisa bar valve product. If fitting a booster pump, we recommend a twin ended booster pump larger than 1 bar is used. - Page 6 AQ100 AQ75:Midas 8/9/15 13:53 Page 6 Typical system diagrams Typical gravity system installation Water level 0.5m 1.5m Typical pumped system installation Water level 0.5m 1.5m...
- Page 7 AQ100 AQ75:Midas 8/9/15 13:53 Page 7 Typical system diagrams continued Typical combination boiler system installation Typical UVHW system installation Typical thermal storage unit system installation...
- Page 8 AQ100 AQ75:Midas 8/9/15 13:54 Page 8 Components - Aqualisa AQ75 bar valve Aqualisa AQ75 bar valve with adjustable height head Components - Aqualisa AQ100 bar valve Screwpack not shown Aqualisa AQ100 bar valve with adjustable height head...
- Page 9 AQ100 AQ75:Midas 8/9/15 13:54 Page 9 Components - Aqualisa 3245F bar valve Aqualisa 3245F bar valve with adjustable height head Please note: Literature not shown in any of the components images.
-
Page 10: Bar Valve Installation
13:54 Page 10 Aqualisa bar valve installation In addition to the guide below it is essential that the written instructions overleaf are read and understood and that you have all the necessary components (shown overleaf) before commencing installation. Failure to install the product in accordance with these instructions may adversely affect the warranty terms and conditions. -
Page 11: Aq75 Adjustable Height Head Installation
If required, refer to the commissioning instructions on page 14 to adjust the maximum temperature override button position. Aqualisa AQ75 adjustable height head installation Hold the front and rear of the grey rail end and carefully, but firmly, pull the chrome cover away from the rail end assembly as shown. - Page 12 Fit the rail end covers into position and push firmly into place. If required, optional outlet flow regulators can be purchased from the Aqualisa customer helpline on 01959 560010. Fit the relevant flow regulator into the brass housing ensuring the O’ring faces the incoming flow. Connect the flow regulator assembly to the valve outlet ensuring the hose washer is correctly fitted.
- Page 13 8/9/15 13:54 Page 13 Aqualisa AQ100 bar valve adjustable height head installation If the handset holder is not already installed onto the rail, carefully remove the adjustable rail bracket, and whilst holding down the button on the handset holder insert the handset holder onto the rail.
- Page 14 8/9/15 13:54 Page 14 Aqualisa 3245F bar valve adjustable height head installation Drill and plug 2 holes 570mm – 585mm apart using the fixings provided, if suitable. Carefully remove the chrome covers from the rail end brackets and set aside.
- Page 15 AQ100 AQ75:Midas 8/9/15 13:54 Page 15 Ensuring the hose washers are in the correct position, secure the handset to the hose and place the handset into the handset holder. The tension of the handset station of the handset holder is factory set. However, it may be necessary to adjust the tension as required.
-
Page 16: Shower Controls
Cleaning & maintenance The Aqualisa bar valve shower system should be cleaned using only a soft cloth and washing up liquid. ! DO NOT USE ABRASIVE CLEANERS. To reduce the need for chemical descaling in hard water areas, your shower head incorporates a ‘clear flow’ system, whereby any scale build up can be broken down by gently rubbing the flexible tips of the jets during use. -
Page 17: Commissioning
Page 17 Aqualisa bar valve commissioning THE AQUALISA BAR VALVE IS PRE-SET TO A SAFE MAXIMUM SHOWER TEMPERATURE. SHOULD IT BE NECESSARY TO RESET THE MAXIMUM TEMPERATURE POSITION, PLEASE OBSERVE THE FOLLOWING PROCEDURE. WE RECOMMEND THE MAXIMUM OUTLET TEMPERATURE IS SET TO 46 Ensure that the hot water system is at normal maximum temperature. -
Page 18: Trouble Shooting Guide
AQ100 AQ75:Midas 8/9/15 13:54 Page 18 Trouble shooting guide Symptom Possible cause Action Check that the supplies Water output is either all hot or Reversed inlet supplies correspond with the inlet all cold, or cold only markings The temperature of the hot... - Page 19 AQ100 AQ75:Midas 8/9/15 13:54 Page 19...
- Page 20 Part No: 701674 Issue 01 Aug 15 Please note that calls may be recorded for training and quality purposes The company reserves the right to alter, change or modify the product specifications without prior warning ® Registered Trademark Aqualisa Products Limited...
Need help?
Do you have a question about the AQ75 and is the answer not in the manual?
Questions and answers