Watlow EZ-ZONE RM User Manual page 102

Dis- Parameter name
play Description
[`o; S 4] Special Output (1 to 4)
Output Size 4
[ o.S4]
[`t; d L] Special Output (1 to 4)
[ t.dL] Time Delay
[`ot; o ] Special Output (1 to 4)
[ ot.o] Output Order
[`uAr] [```1]
[`Set] [`uAr]
Variable Menu Variable 1
[tyPE] Variable 1 to 8
[tyPE] Data Type
Set the variable's data type.
[Unit] Variable 1 to 8
[Unit] Units
Set the variable's units.
[`Dig]
Variable 1 to 8
[ dig] Digital
Set the variable's value.
[anLg]
Variable 1 to 8
[AnLg] Analog
Set the variable's value.
[gLbL]
[`Set]
Global Menu
[`C_F] Global
Display Units
[ C_F]
Select which scale to use for
temperature.
[AC; L F] Global
AC Line Frequency
[AC.LF]
Set the frequency to the ap-
plied ac line power source.
[`PRo]
[`Set]
Profile Menu
[R; t yp]
Profile
[R.tyP] Ramping Type
[P; t yp]
Profile
[P.tyP] Profile Type
Set the profile startup to be
based on a set point or a pro-
cess value.
Note: Some values will be rounded off to fit in the four-character display.
Full values can be read with other interfaces.
If there is only one instance of a menu, no submenus will appear.
®
Wa t low EZ-ZO N E R M Sy s te m
Control Module
Range
0 to 9,999
0 to 9,999 seconds
[`Lin] Linear (1509)
[`Pro] Progressive (1510)
[```8]
[`uAr]
to Variable 8
[AnLg] Analog (1215)
[`Dig] Digital (1220)
[nonE] None (61)
[`r; t p] Relative Temperature
(1541)
[`A; t p] Absolute Temperature
(1540)
[``rh] Relative Humidity (1538)
[PWr] Power (73)
[`Pro] Process (75)
[`oFF] Off (62)
[``on] On (63)
-1,999.000 to 9,999.000
[```F] °F (30)
[```C] °C (15)
[``50] 50 Hz (3)
[``60] 60 Hz (4)
[````] Rate (81)
[``ti] Time (143)
[StPt] Set Point (85)
[`Pro] Process (75)
•
• Setup Page
Default Appears If
0 Function is set
to Sequencer
0 Function is set
to Sequencer
Linear Function is set
to Sequencer
Analog always
Absolute Data Type is set
Temper- to Analog.
ature
Off Data Type is set
to Digital.
0.0 Data Type is set
to Analog.
°F always
60 Hz always
Time always
Set Point always
•
99 Chapter 6 Controll er Modul e Se tup Pa ge
Modbus CIP Data
for Type
Class
instance 1 &
Instance
[offset] Read/
Attribute
see below Write
hex (dec)
5020 87 (135) float
[offset 80] 1 to 4
RWES
1F (31)
5010 87 (135) int
[offset 80] 1 to 4
RWES
1A (26)
5012 87 (135) int
[offset 80] 1 to 4
RWES
1B (27)
4800 66 (102) int
[offset 20] 1 to 8
RWES
1
4812 66 (102) int
[offset 20] 1 to 8
RWES
7
4802 66 (102) int
[offset 20] 1 to 8
RWES
2
4804 66 (102) float
[offset 20] 1 to 8
RWES
3
RWES
1026 6A (106) int
[offset 30] 1 to C RWES
(12)
4
5354 7A (122) int
1 RWE
26 (38)
5294 7A (122) int
1 RWE
8
inst. (n) reg. = R: Read
inst. 1 reg. + W: Write
((n-1) * offset) E:
EEPROM
S:
User Set