Siemens SINUMERIK 840D sl Function Manual page 2145

FC9 Out: Active, 20
FC9 Out: Done, 20
FC9 Out: Error, 20
FC9 Out: StartError, 20
FC9: Start (measuring in Jog mode), 26
Feed disable, 134
Feed rate override, 130
Feed rate override (axisspecific), 137
Feed rate override active, 135
Feed rate override selected for rapid traverse, 136
Feed stop (Geometry axis 1 to 3), 135
Feed stop/spindle stop (axisspecific), 140
Fixed stop reached, 73
Follow up operation, 32
Followup mode active, 43
Gear is changed over, 116
Hardware limit switches plus and minus, 68
Heatsink temperature prewarning, 55
Higraph first error display, 14, 15
HMI CPU1 Ready, 9
HMI-Alarm is active, 8
HMI-CPU2-Ready (to BTSS or to MPI), 9
i2t monitoring, 64
Interface signals: Activate machinerelated
protection zone, 65
Interface signals: Enable protection zones, 65
Interrupt processing active, 99
Invert M3/M4, 118
JOG mode, 79
Key disable, 13
Key-operated switch position, 7
Last action block active, 94
Load, 25
Load part program, 17
Lubrication pulse, 46
M fct. 1-5 not included in list, 74
M function for spindle, 128
M(d) less than M(dx), 58
M, S, T, D, H, F functions Additional info "Quick"
(quick acknowledgment), 75
M, S, T, D, H, F functions Modification, 74
M00/M01 active, 93
M02/M30 active, 95
Machine function REF, 82
Machine function REPOS, 82
Machine function TEACH IN, 82
Machinerelated protection zone preactivated, 66
Machinerelated protection zone violated, 67
MDA mode, 79
Mode change disable, 19
Mode changeover inhibit, 80
Mode group number, 26
Basic logic functions: NC/PLC interface signals (Z1)
Function Manual, 11/2006, 6FC5397-0BP10-2BA0
Mode group ready, 86
Mode group reset, 81
Mode group stop, 80
Mode group stop axes plus spindles, 81
Motor selection A, B, 40
Motor selection in progress, 41
Motor temperature prewarning, 53
n(act) equals n(set), 60
n(act) less than n(min), 60
n(act) less than n(x), 60
NC Ready, 10
NC start, 90
NC start disable, 90
NC stop, 91
NC Stop at block limit, 90
NC Stop axes plus spindles, 91
NCK alarm is active, 10
NCK alarm with processing stop present, 28
NCK battery alarm, 11
NCK CPU Ready, 9
NCU 573 heatsink temperature alarm, 11
OK, 22, 24
Oscillation controlled by the PLC, 119
Oscillation speed, 119
Override active, 139
Overstore active:DB21 DBX318.7, 28
Path axis, 107
PCU Battery alarm, 8
PCU temperature limit, 8
PLC action completed, 88
PLC index, 18, 19
PLC line offset, 18, 19
Position controller active, 44
Position measuring systems 1 and 2, 33
Position reached with exact stop coarse, 70
Position reached with exact stop fine, 70
PROG-EVENT-DISPLAY, 105
Program level abort, 90
Program status aborted, 98
Program status interrupted, 98
Program status running, 96
Program status stopped, 97
Program status wait, 97
Program test active, 96
Programming area selection, 15
Pulse enable, 42
Pulses enabled, 52
Rampfunction generator fast stop, 38
Rampfunction generator fast stop active, 47
Ramp-up completed, 56
Rampup times, 37
Rapid traverse override, 132
Index
149