Siemens SINUMERIK 840D sl Function Manual page 2144

Index
DBX94.7, 61
DBX95.0, 63
DBX95.7, 64
I
Interface signals
611D Ready, 10
Acknowledge EMERGENCY STOP, 109
Acknowledge fixed stop reached, 71
Action block active, 93
Activate associated M1, 74
Activate channelspecific protection zone, 65
Activate dry run feed, 129
Activate fixed feed rate 1 - 4 for machine axes, 139
Activate fixed feed rate 1 - 4 for path/geometry
axes, 137
Activate M01, 88
Activate program test, 89
Activate referencing, 110
Activate single block, 87
Activate travel to fixed stop, 73
Active, 25
Active drive parameter set A, B, C, 48
Active G function of groups 1 to 60, 101
Active JOG mode, 86
Active machine function REF, 87
Active machine function TEACH IN, 86
Active mode AUTOMATIC, 85
Active mode MDA, 85
Active motor A, B, 49
Active or passive file system, 18, 19
Active REPOS machine function, 87
Active spindle control mode, 127
Active spindle mode oscillation mode, 127
Active spindle positioning mode, 127
Actual direction of rotation clockwise, 126
Actual gear stage A to C, 115
Actual value in WCS, 14
Air temperature alarm, 11
Alarm area selection, 15
All axes stationary, 70
All axes that have to be referenced are
referenced, 112
All channels in the reset state, 86
Analog spindle 1, utilization in percent, 15
Analog spindle 2, utilization in percent, 15
Approach block active, 93
Associated M01/M00 active, 78
ASUB is stopped, 102
AT box ready, 8
AUTOMATIC mode, 79
148
Axis/spindle disable, 29
Axis/spindle stops, 44
Block search active, 95
Block search via program test is active, 102
Cancel alarm cleared, 21
Change gear stage, 124
Channel is ready, 100
Channel number (FC9: ChanNo), 26
Channel number of the machine control panel to
HMI, 15
Channel status active, 98
Channel status interrupted, 99
Channel status reset, 99
Channelspecific NCK alarm is active, 27
Channelspecific protection zone preactivated, 66
Channelspecific protection zone violated, 67
Clamping in progress, 68
Clear cancel alarms, 13
Clear recall alarms, 14
COM1, 16, 22
COM2, 16, 22
Controller enable, 34
Controller parameter set switchover (checkback
signal), 46
Controller parameter set switchover (request), 37
Current controller active, 46
D function 1, 76
Darken screen, 12
Data transfer error, 26
Delete distancetogo (axisspecific)/Spindle reset, 36
Delete distancetogo (channelspecific), 27
Delete S value, 118
Disable parameter set switchover commands from
NC, 37
displayed channel number from HMI, 22
Drive parameter set selection A, B, C, 39
Drive Ready, 50
Drive test travel enable, 28
Drive test travel request, 43
Dry run feed rate selected, 136
EMERGENCY STOP, 108
EMERGENCY STOP active, 110
Enable travel to fixed stop, 72
Encoder limit frequency exceeded, 69
Error, 22, 24
Error RS232C, 24
Extended address F functions 1 to 6, 77
Extended address H functions 1 to 3, 77
Extended address M functions 1 to 5, 75
Extended address S functions 1 to 3, 76
External zero offset, 108
F function for positioning axis, 143
Basic logic functions: NC/PLC interface signals (Z1)
Function Manual, 11/2006, 6FC5397-0BP10-2BA0