HP 16600A Series Installation Manual page 118

Copyright Hewlett-Packard
C Safety
Company 1998
This apparatus has been designed
All Rights Reserved.
and tested in accordance with IEC
Publication 1010, Safety
Reproduction, adaptation, or
Requirements for Measuring
translation without prior written
Apparatus, and has been supplied
permission is prohibited, except
in a safe condition. This is a
as allowed under the copyright
Safety Class I instrument
laws.
(provided with terminal for
protective earthing). Before
Restricted Rights Legend.
applying power, verify that the
Use, duplication or disclosure by
correct safety precautions are
the U.S.Government is subject to
taken (see the following
restrictions as set forth in
warnings). In addition, note the
subparagraph (c)(1)(ii) of the
external markings on the
Rights in Technical Data and
instrument that are described
Computer Software clause at
under "Safety Symbols."
DFARS 252.227-7013 for DOD
agencies, and subparagraphs
Warning
(c)(1) and (c)(2) of the
Commercial Computer Software
instrument, you must connect the
Restricted Rights clause at FAR
protective earth terminal of the
52.227-19 for other agencies.
instrument to the protective
conductor of the (mains) power
Hewlett-Packard Company
cord. The mains plug shall only
3000 Hanover Street
be inserted in a socket outlet
Palo Alto, California 94304
provided with a protective earth
U.S.A.
contact. You must not negate the
protective action by using an
extension cord (power cable)
Document Warranty
without a protective conductor
The information contained in this
(grounding). Grounding one
document is subject to change
conductor of a two-conductor
without notice.
outlet is not sufficient protection.
Hewlett-Packard makes no
warranty of any kind with
rated current, voltage, and
regard to this material,
specified type (normal blow, time
including, but not limited to,
delay, etc.) should be used. Do
the implied warranties of
not use repaired fuses or short-
merchantability or fitness for a
circuited fuseholders. To do so
particular purpose.
could cause a shock or fire
hazard.
Hewlett-Packard shall not be
liable for errors contained herein
or for damages in connection
with the furnishing, performance,
or use of this material.
Hewlett-Packard
P.O. Box 2197
1900 Garden of the Gods Road
Colorado Springs, CO. 80901
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Service instructions are for
trained service personnel. To
avoid dangerous electric shock,
do not perform any service unless
qualified to do so. Do not
attempt internal service or
adjustment unless another person,
capable of rendering first aid and
resuscitation, is present.
If you energize this instrument
by an auto transformer (for
voltage reduction), make sure the
common terminal is connected to
the earth terminal of the power
source.
Whenever it is likely that the
ground protection is impaired,
Before turning on the
you must make the instrument
inoperative and secure it against
any unintended operation.
Do not operate the instrument
in the presence of flammable
gasses or fumes. Operation of
any electrical instrument in such
an environment constitutes a
definite safety hazard.
Do not install substitute parts or
perform any unauthorized
modification to the instrument.
Capacitors inside the instrument
may retain a charge even if the
Only fuses with the required
instrument is disconnected from
its source of supply.
Use caution when exposing or
handling the CRT. Handling or
replacing the CRT shall be done
only by qualified maintenance
personnel.
Safety Symbols
Instruction manual symbol: the
product is marked with this
symbol when it is necessary for
you to refer to the instruction
manual in order to protect against
damage to the product.
Hazardous voltage symbol.
Earth terminal symbol: Used to
indicate a circuit common
connected to grounded chassis.
WARNING
The Warning sign denotes a
hazard. It calls attention to a
procedure, practice, or the like,
which, if not correctly performed
or adhered to, could result in
personal injury. Do not proceed
beyond a Warning sign until the
indicated conditions are fully
understood and met.
CAUTION
The Caution sign denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like, which, if not correctly
performed or adhered to, could
result in damage to or destruction
of part or all of the product. Do
not proceed beyond a Caution
symbol until the indicated
conditions are fully understood or
met.