Advertisement
Quick Links
Midmount Toolbar System
Sand Pro
Model No. 08731—Serial No. 312000001 and Up
Important: Before installing the mid-mount toolbar system, you should obtain one of the toolbars available for use
with the system. For more information, contact an Authorized Toro Distributor.
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
© 2014—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
/Infield Pro
Description
No parts required
Bolt (5/16 x 2-1/4 inches)
Nut (5/16 inch)
Scarifier lift-handle assembly
Bolt (1/2 x 3-1/4 inches)
Thin locknut (1/2 inch)
Detent plate
Knob
Pivot tube
Extension spring
Spring rod
Pivot tube bracket
Bolt (3/8 x 3 inches)
Locknut (3/8 inch)
Spring bracket
Bolt (3/8 x 2-3/4 inches)
Adjustable rod assembly
Bolt (1/2 x 1-1/2 inches)
Locknut (1/2 inch)
Screen panel
Pan-head screw (#10 x 1/2 inch)
Right-hand saddle assembly
Left-hand saddle assembly
Bolt (5/16 x 1 inch)
Locknut (5/16 inch)
Toolbar (sold separately)
Register at www.Toro.com.
®
3040 and 5040 Traction Unit
Qty.
–
2
2
1
2
2
1
1
1
1
1
2
4
6
1
1
1
1
2
1
2
1
1
4
4
1
Original Instructions (EN)
Form No. 3372-400 Rev C
Operator's Manual
Use
Do the pre-installation setup.
Install the scarifier lift-handle assembly.
Install the pivot tube and the tension
spring.
Install the adjustable rod assembly.
Install the screen panel and saddles.
Install a toolbar.
All Rights Reserved *3372-400* C
Printed in the USA
Advertisement
Related Manuals for Toro 08731
Summary of Contents for Toro 08731
- Page 1 Model No. 08731—Serial No. 312000001 and Up Operator's Manual Important: Before installing the mid-mount toolbar system, you should obtain one of the toolbars available for use with the system. For more information, contact an Authorized Toro Distributor. Setup Loose Parts Use the chart below to verify that all parts have been shipped.
-
Page 2: No Parts Required
Procedure Description Qty. Lever assembly Bolt (5/16 x 2 inches) Locknut (5/16 inch) Pivot tab Toolbar link Carriage bolt (3/8 x 1-1/4 inches) Spacer Install the toolbar lift pedal. Washer (1 inch) Locknut (3/8 inch) Pedal lever assembly Retaining ring Washer (7/8 inch) Bolt (5/16 x 1 inch) Eccentric bolt... - Page 3 step. If you use the thick ones, they will not lock on and will eventually fall off. Note: The handle assembly is installed through the bottom of the traction unit by guiding the handle up through the opening made by removing the screen panel.
- Page 4 Figure 4 Figure 5 1. Handle lift assembly pivot 2. Locknut 1. Locknut (3/8 inch) 5. Extension spring 2. Pivot tube bracket 6. Spring rod 10. Check the clearance between the lift handle assembly 3. Bolt (3/8 x 3 inch) 7.
- Page 5 7. Tighten all fasteners, but do not tighten the locknut 5. Move the ball joint on the short end of the adjustable that secure the spring rod at this time. rod around the adjustable rod lever on the pivot tube until it is on the left side of the rod lever.
- Page 6 Installing the Screen Panel and Saddles Parts needed for this procedure: Screen panel Figure 10 Pan-head screw (#10 x 1/2 inch) 1. Bolt (5/16 x 1 inch) 3. Lift arm Right-hand saddle assembly 2. Saddle 4. Locknut (5/16 inch) Left-hand saddle assembly Bolt (5/16 x 1 inch) Locknut (5/16 inch) Procedure...
- Page 7 Installing the Toolbar Lift Pedal Parts needed for this procedure: Lever assembly Bolt (5/16 x 2 inches) Locknut (5/16 inch) Pivot tab Toolbar link Carriage bolt (3/8 x 1-1/4 inches) Spacer Washer (1 inch) Figure 11 Locknut (3/8 inch) 1. Toolbar 3.
- Page 8 Figure 13 1. Lever assembly 3. Bolt (5/16 x 2 inches) 2. Pivot tube 4. Locknut (5/16 inch) Figure 15 1. Toolbar link 4. Retaining ring 2. Loosely install the center hole of the pivot tab to the 2. Pedal lever assembly 5.
- Page 9 Adjusting the Pivot Spring Tension and the Adjustable Rod Assembly No Parts Required Procedure 1. Position the lift handle in the top detent position. Figure 16 2. Measure the distance between the traction unit frame 1. Pivot tab 5. Washer (1 inch) and the pivot tube as shown in Figure 17.
- Page 10 • Important: The eccentric bolt will not rotate 360 To increase the gap, shorten the rod. degrees. When it stops, do not attempt to force • To decrease the gap, lengthen the rod. it further or you will damage it. Instead, rotate it C.
-
Page 11: Operation
5. Measure the gap from the toolbar teeth to the ground 2. Store the documentation in a safe place. on the side that requires leveling, then use the following Operation table to determine which shim to install based on the gap measurement: •... - Page 12 Figure 23 1. Adjustable rod assembly 3. Decrease downward pressure 2. Spring sleeve casting Use the following table and figure as a guide for adjusting the downward toolbar pressure (Figure 24). Spring Force Chart Dimension (inches) Force (pounds) 3.00 2.88 2.75 2.62 2.50...
-
Page 13: Troubleshooting
1. The traction unit tilts when turning tight 1. Install the optional stiffer sidewall tires turning the machine corners or circles. available from your Authorized Toro Distributor. The machine stops when it hits an obstacle 1. The adjuster rod is installed incorrectly 1. - Page 14 Notes:...
- Page 15 Notes:...
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.