Table of Contents
Advertisement
Quick Links
Register at www.Toro.com.
Original Instructions (EN)
18in, 21in, and 26in; 8-Blade,
11-Blade, and 14-Blade Cutting
Units
Greensmaster
Model No. 04823—Serial No. 400000000 and Up
Model No. 04824—Serial No. 400000000 and Up
Model No. 04832—Serial No. 400000000 and Up
Model No. 04833—Serial No. 400000000 and Up
Model No. 04834—Serial No. 400000000 and Up
Model No. 04842—Serial No. 400000000 and Up
Model No. 04843—Serial No. 400000000 and Up
Form No. 3431-366 Rev C
®
1018, 1021, and 1026 Mower
*3431-366* C
Advertisement
Table of Contents
Related Manuals for Toro Groundmaster 1018
Summary of Contents for Toro Groundmaster 1018
- Page 1 Model No. 04832—Serial No. 400000000 and Up Model No. 04833—Serial No. 400000000 and Up Model No. 04834—Serial No. 400000000 and Up Model No. 04842—Serial No. 400000000 and Up Model No. 04843—Serial No. 400000000 and Up *3431-366* C Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Whenever you need service, genuine Toro parts, or Safety and Instructional Decals ......3 additional information, contact an Authorized Service Setup ................ 4 Dealer or Toro Customer Service and have the model 1 Installing the Roller .......... 4 and serial numbers of your product ready. Figure 1... -
Page 3: Safety
• Use only accessories, attachments, and functioning properly on the machine. replacement parts approved by Toro. • Keep clear of any discharge opening. • Keep bystanders and children out of the operating Blade Safety area. -
Page 4: Setup
Traction Unit Procedure No Parts Required The cutting unit is shipped without a front roller. Obtain a roller from your authorized Toro dealer and Procedure install it on the cutting unit, as follows: Remove the plow bolt, washer, and flange nut Install the cutting unit to the traction unit;... -
Page 5: Product Overview
Refer to your traction unit Operator’s Manual. Attachments/Accessories A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all approved attachments and accessories. -
Page 6: Maintenance
Maintenance Checking the Reel-Driveshaft Grease Point Service Interval: Yearly Remove the hardware that secures the reel-drive assembly to the side plate (Figure g276424 Figure 6 1. Reel driveshaft Use the previously removed socket-head screws, washers, and spacers to secure the reel-drive assembly to the side plate. -
Page 7: Adjusting The Bedknife-To-Reel Contact
This procedure can be performed with the edges needed for precision cutting (Refer to cutting unit installed to the traction unit. the Toro Manual for Sharpening Reel and Shut off the traction-unit engine. Rotary Mowers, Form No. 09168SL). Access the cutting unit by lowering the... - Page 8 Note: This will make later adjustments easier. for precision cutting (Refer to the Toro Manual for Insert a 0.05 mm (0.002 inch) shim between the Sharpening Reel and Rotary Mowers, Form No.
-
Page 9: Setting The Cutting Unit To Match Turf Conditions
Setting the Cutting Unit to Match Turf Conditions Use the following tables to determine the proper bedknife and roller that is needed to match your turf conditions. Contact your authorized Toro distributor to acquire additional bedknives and rollers. Refer to Adjusting the Clip Rate (page 12) for instructions to set the appropriate clip rate for your turf conditions. - Page 10 Bedknives (cont'd.) Greensmaster 6.0 mm (0.250 inch) and up Standard Greensmaster 1026 93-9015 Low Cut 1026 Greensmaster 1.52 to 3.1 mm (0.060 Longer wearing 117-1548 Edgemax Tournament 1026 to 0.122) Edgemax Short Greensmaster 1.57–3.1 mm More aggressive 139-4322 Microcut 1026 (0.062–0.125 inch) Edgemax Short Greensmaster...
-
Page 11: Performing The Height-Of-Cut Adjustment
Performing the Adjusting the Height of Cut Loosen the locknuts that secure the height-of-cut Height-of-Cut Adjustment arms to the cutting-unit side plates (Figure 12). Set the height of cut to the desired height using a height-of-cut gauge, and ensure that your cutting unit is equipped with a bedknife that is best suited for your desired height of cut;... -
Page 12: Adjusting The Clip Rate
• For a height of cut greater than 16 mm (0.625 inch), install the High Height-of-Cut Kit. Contact your authorized Toro distributor to acquire this kit. Adjusting the Clip Rate The clip rate is determined by the following machine g275967... -
Page 13: Adjusting The Grass Shield
Adjusting the Grass Shield Adjust the grass shield to ensure that the clippings are cleanly discharged from the reel area, as follows: Note: The shield is adjustable to compensate for changes in turf conditions. Adjust the shield closer to the reel when the turf is extremely dry. By contrast, adjust the shield further away from the reel when the turf conditions are wet. -
Page 14: Servicing The Bedbar
Ideally, take the cutting unit to your authorized Toro distributor for service. Refer to the Service Manual for your traction unit for complete instructions, special tools, and diagrams for servicing the bedknife. -
Page 15: Servicing The Bedknife
Installing the Bedbar Install the bedbar, positioning the mounting ears between the washers and the bedbar-adjusting screw (Figure 18). Secure the bedbar to each side plate with the bedbar bolts (nuts on bolts) and 3 washers (6 total). Position a nylon washer on each side of the side-plate boss. - Page 16 Preparing the Reel for Grinding Relief-Grinding the Reel Ensure that all cutting unit components are in The new reel has a land width of 1.3 to 1.5 mm (0.030 good condition and correct any issues before to 0.050 inch) and a 30° relief grind. grinding.
-
Page 17: Backlapping The Cutting Unit
2 degrees of the very important. recommended top grind angle. Use the angle indicator (Toro Part No. 131-6828) and the angle-indicator mount (Toro Part No. 131-6829) to Backlapping the Cutting check the angle that your grinder produces and then correct for any grinder inaccuracy. - Page 18 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 19 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 20 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.