Toro 30555 Operator's Manual
52 in side discharge mower traction unit
Hide thumbs
Also See for 30555:
- Operator's manual (28 pages) ,
- Operator's manual (24 pages) ,
- Operator's manual (24 pages)
Related Manuals for Toro 30555
Summary of Contents for Toro 30555
- Page 1 Form No. 3383-271 Rev A 52in Side Discharge Mower Groundsmaster ® 200, 3320 and 3280-D Series Traction Unit Model No. 30555—Serial No. 314000001 and Up *3383-271* A Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Introduction
You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product. -
Page 3: Table Of Contents
Safety ................3 in effect at the time of production. Safe Operating Practices........... 3 Toro Mower Safety ..........5 Improper use or maintenance by the operator or owner can Safety and Instructional Decals ......... 6 result in injury. To reduce the potential for injury, comply Setup ................ -
Page 4: Maintenance And Storage
• • Remove equipment from the truck or trailer and refuel it Look behind and down before backing up to be sure of on the ground. If this is not possible, then refuel such a clear path. equipment with a portable container, rather than from a •... -
Page 5: Toro Mower Safety
The following list contains safety information specific to Toro units to the ground. products or other safety information that you must know that is not included in the CEN, ISO, or ANSI standard. -
Page 6: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 107-2916 1. Remove the ignition key and read the 2. - Page 7 117–4979 2WD: GM 228D = 0 GM 225 = 25 kg(55 lbs) 4WD: 0 1. Entanglement hazard, belt—stay away from moving parts, keep all guards and shields in place. 105–9551 1. Warning—read the 2. Lower the cutting deck Operator's Manual. when traveling down slopes.
-
Page 8: Setup
Note: When installing the 52 inch deck onto a Spacer Groundsmaster 200 Series traction unit, the Weight Transfer Pivot pin Kit, Toro Part Number 70-8090 must be installed. Cotter pin (5/32 x 1-3/4 inches) Procedure 1. On one side of the traction unit, loosen (do not remove) the wheel nuts securing the wheel and tire assembly to the front wheel studs. -
Page 9: Installing The Carrier Frame
2. Jack up the machine until the front wheel is off of the floor. Use jack stands or block the machine to prevent it from accidentally falling. 3. Remove the wheel nuts and slide the wheel and tire assembly off of the studs. 4. -
Page 10: Installing The Cutting Unit
G010543 Figure 5 1. Castor wheel assembly 3. Thrust washers 4. Lynch pin 2. Carrier frame G010545 3. Mount a rear cradle to each lift arm with 3 bolts (3/8 x Figure 7 2 inches), spacers, and flange nuts as shown in Figure 6. 1. -
Page 11: Installing The Ce Decal
Operator's Manual to determine the combinations of weight required. Order the parts from your 1. 25 mm (1 inch) 6. 89 mm (3-1/2 inches) local Authorized Toro Distributor. 2. 38 mm (1-1/2 inches) 7. 102 mm (4 inches ) 3. 51 mm (2 inches) 8. -
Page 12: Product Overview
Contact your Authorized Service Dealer or Figure 11 Distributor or go to www.Toro.com for a list of all approved 1. 25 mm (1 inch) 6. 89 mm (3-1/2 inches) attachments and accessories. -
Page 13: Checking The Gear Box Lubricant
Checking the Gear Box Note: The deflector is spring loaded into its downward normal operating position (Figure 11), but the operator can Lubricant temporarily swing it out of the way to facilitate loading in a trailer or when otherwise necessary. The gear box is designed to operate on SAE 80-90 wt. -
Page 14: Maintenance
Maintenance Important: The fasteners on the covers of this machine are designed to remain on the cover after removal. Loosen all of the fasteners on each cover a few turns so that the cover is loose but still attached, then go back and loosen them until the cover comes free. -
Page 15: Separating The Cutting Unit From The Traction Unit
Separating the Cutting Unit 3. Pull the castor spindle out of the mounting tube. Allow the thrust washers to remain on the bottom of the from the Traction Unit spindle. 1. Position the machine on a level surface, raise the cutting 4. -
Page 16: Checking For A Bent Blade
The blade must be replaced if a solid object is hit, the blade is out-of-balance, worn, or bent. Always use genuine Toro replacement blades to ensure safety and optimum performance. Never use blades made by other manufacturers because they could be dangerous. -
Page 17: Inspecting And Sharpening The Blade
• Replace a worn or damaged blade with a edges and the sail, which is the turned up portion opposite new Toro blade to ensure continued safety the cutting edge, contribute to a good quality-of-cut. The certification of the product. -
Page 18: Checking And Correcting Mismatch Of Blades
Checking and Correcting the dimensions of all 3 blades must not exceed 10 mm (3/8 inch). If the difference exceeds specifications, Mismatch of Blades proceed to step 9. If one cutting blade cuts lower than the others, correct them 9. Remove the bolts, flat washers, and locknuts from as follows: the outer spindle in the area where the shims must be added. -
Page 19: Replacing The Grass Deflector
E. If the height is within the specified dimension, the large nut is required. If the idler is not adjusted to these install the lynch pin, set the height-of-cut to the specifications, an adjustment is necessary. proper height, and resume operation. 1. - Page 20 5. To install a new belt, the gear box base must be removed. To do this, remove the 4 carriage bolts and locknuts holding the gear box base. 6. Install the new belt around the gear box pulley, spindle pulleys, stationary idler pulley, and adjustable idler pulley (Figure 29).
-
Page 21: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The cutting unit will not cut or cuts poorly. 1. The blades are dull. 1. Sharpen the blades. 2. One or more blades are bent or 2. Replace the blades. damaged. 3. The spindle bolts are loose. 3. - Page 22 Notes:...
- Page 23 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
-
Page 24: The Toro Total Coverage Guarantee
Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.