Table of Contents
Advertisement
- SQ: 41, 42, 43, 44, 45, 51, 52, 53, 54
f These can be set only when the target pattern is selected in the background.
Either operate the fader lever or press the <AUTO> button to check the wipe operation.
Example) When [X] is set to [−50], and [Y] is set to [−50]
The next screen (or key) appears from the bottom left, and wipes in towards the center of the screen.
Setting the wipe direction switching mode
1
Select the <OPR> button → [OTHER SETTINGS] → [Transition] tab.
2
Select the items in [N/R Recall] in the [BKGD WIPE] column.
[Off]
[Normal]
Setting trimming, aspect ratio
Set the behavior for the trimming and aspect ratio. This is applied to the background transition.
1
Select the <ME1>/<ME2> button → [BKGD] → [Border/Trim] tab.
2
Set the items in the [Trim Mode] column.
f Set the trimming for the pattern waveforms of SQ and 3D.
f This is enabled when the following pattern waveforms are selected.
- SQ: 41, 51 - 54
[Off]
[4:3 Smooth]
[Manual]
3
Select [Trim] in the R menu, and set the trimming positions with [Left], [Top], [Right], and [Bottom] in the encoder menu.
f The trimming position is set as follows according to the setting of the [Pair] item in the [Trim] column.
- [OFF]: The amount of trimming is set individually for [Left], [Right], [Top], and [Bottom].
- [ON]: The amount of trimming is set as a pair for [Left] and [Right], [Top] and [Bottom], so the amount changes to be the same. (Symmetrical
vertically or horizontally)
f The parameters can also be changed with the Positioner.
Set the behavior with [Positioner] in the encoder menu. [Positioner] switches between [L/T] and [R/B] each time you select it.
- [L/T]: [Left] and [Top] are changed.
- [R/B]: [Right] and [Bottom] are changed.
4
Select [Wipe Aspect] in the R menu, and set [WipeAspect] in the encoder menu.
f Adjust the aspect ratio of the wipe pattern.
f The following pattern waveforms are changed.
- WIPE: 11 - 15
- SQ: 42 - 45
f SQ41 and 51 to 54 are not applicable. The aspect ratio is adjusted with [Left], [Top], [Right], or [Bottom].
5
Select an item in [Smooth] in the [Trim] column.
[OFF]
[ON]
f Modifies the next pattern waveforms.
- WIPE: 11 - 15
- SQ: 42 - 45
f SQ: 41, 51 to 54 and 3D: 107 are also applicable.
Setting the turn page effect
Set the parameters for the Page Turn effect.
f Modify the following pattern waveforms.
- 3D: 99, 100, 101, 102
1
Select the <ME1>/<ME2> button → [BKGD] → [Pos/Modify] tab.
2
Select the item in [Light].
[OFF]
[ON]
f This setting is also applied to the following pattern waveforms.
- 3D: 109, 110
Chapter 5 Basic Operations — Wipe
The wipe direction ([Normal]/[Reverse]) is maintained for each background wipe preset.
When you change the background transition type ([MIX]/[WIPE]) or the background wipe preset, the wipe direction
switches to [Normal].
Does not perform trimming.
Performs trimming in the 4:3 aspect ratio, and smoothly executes transition to the 16:9 video.
Trimming occurs at the trimming position set in [Trim] in the R menu.
The aspect ratio for set wipe pattern will be constant regardless of the transition.
For SQ waveform, it may become discontinuous at the edge of transition.
The aspect ratio is changed from the aspect ratio of the preset wipe pattern to the standard ratio in accordance with the
transition.
Does not add the lighting effect.
Adds the lighting effect.
– 55 –
Advertisement
Table of Contents
