1. Manuals
  2. Brands
  3. NI Manuals
  4. Chassis
  5. cRIO-9082
  6. User manual

NI cRIO-9082 User Manual

Reconfigurable embedded chassis with integrated intelligent real-time controller for compactrio
Hide thumbs Also See for cRIO-9082:
Table of Contents

Advertisement

Quick Links

Download this manual
NI cRIO-9082 User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the cRIO-9082 and is the answer not in the manual?

Questions and answers

Related Manuals for NI cRIO-9082

Summary of Contents for NI cRIO-9082

  • Page 1 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
  • Page 2 USER MANUAL NI cRIO-9082 Reconfigurable Embedded Chassis with Integrated Intelligent Real- Time Controller for CompactRIO This document describes the features of the National Instruments cRIO-9082 and contains information about mounting and operating the device. Intel Core i7-660UE VGA Port 1.33 GHz Dual-Core...
  • Page 3 NI-cRIO-9082-1856AAA. Finding the cRIO-9082 on the Network (Static IP) Complete the following steps to find the cRIO-9082 on the network if the host computer is using a static IP address. The following instructions are for host computers running Windows 7.

  • Page 4: Configuring Dip Switches

    Click Properties. Record the IP address, Subnet mask, and Default gateway address. You need these settings to configure the network settings of the cRIO-9082 and to restore the network settings of the host computer. You can also access these settings by opening the Start menu,...
  • Page 5 Keep this switch in the OFF position during normal operation. If the switch is in the ON position at startup, the cRIO-9082 launches only the essential services required for updating its configuration and installing software. The LabVIEW Real-Time engine does not launch.

  • Page 6: Installing An Operating System

    Restoring the Hard Drive to Factory Default Condition (Windows Only) You can restore the hard drive of the cRIO-9082 to factory default condition either from a recovery partition on the hard drive or from the NI Embedded Controller OEM Re-Installation DVD shipped with thecRIO-9082.

  • Page 7: Rs-232 Serial Port

    4. RJ-45 Ethernet Ports 1 and 2 RS-232 Serial Port The cRIO-9082 has an RS-232 serial port to which you can connect devices such as displays or input devices. Use the Serial VIs to read from and write to the serial port. Refer to the LabVIEW Help for information about the Serial VIs.
  • Page 8 RI/WAKE You can use the Ring Indicator (RI) on pin 9 to wake the controller from a low-power state. You can drive RI with a logic level high to wake the cRIO-9082. Refer to the specifications on ni.com/manuals for the RI wake voltage.
  • Page 9 No Connect Isolated GND The following figure shows how to wire several NI FP-1001 banks in an RS-485/422 network controlled by the cRIO-9082. Only two FP-1001 banks are shown, but the cRIO-9082 can control up to 24 nodes. Install 120 Ω termination resistors at each end of the network.

  • Page 10: Usb Ports

    778674-01 MXI Express Port You can use the MXI Express port on the cRIO-9082 to connect to a MXI Express chassis. Complete the following steps to connect one or more cRIO-9082 to a MXI Express device. Make sure the MXI Express device is configured and powered off.
  • Page 11 Caution Do not hot-swap USB devices while the cRIO-9082 is in a hazardous location or connected to high voltages. If the cRIO-9082 is not in a hazardous location, you can connect and disconnect USB devices without affecting operation. Video Port (VGA) The cRIO-9082 VGA port outputs graphics using VESA standard VGA analog signaling.

  • Page 12: Gigabit Ethernet Ports

    RJ-45 Gigabit Ethernet Ports The cRIO-9082 has two tri-speed RJ-45 Gigabit Ethernet ports. By default, both Ethernet ports are enabled and configured to obtain an IP address automatically. The Ethernet ports can be configured in MAX. The following table shows the pinout for the RJ-45 Gigabit Ethernet ports.

  • Page 13: Power Connector

    If you apply power to both the V1 and V2 inputs, the cRIO-9082 operates from the V1 input. If the input voltage to V1 is insufficient, the cRIO-9082 operates from the V2 input.

  • Page 14: Power Button

    The FPGA continues to run unless you select the Autoload on Any Device Reset boot option. CMOS Reset Button The cRIO-9082 has a CMOS reset button that you can use to reset the CMOS and the BIOS. LEDs The cRIO-9082 provides the following LEDs.

  • Page 15: Drive Led

    The DRIVE LED is lit yellow when an internal drive is being accessed. STATUS LED Indicators The STATUS LED is off during normal operation. The cRIO-9082 indicates specific software error conditions by flashing the STATUS LED yellow a certain number of times every few seconds, as shown in the following table.
  • Page 16 If the problem persists, contact National Instruments. The cRIO-9082 indicates specific hardware error conditions by flashing the STATUS LED red a certain number of times every few seconds, as shown in the following table. Table 13. STATUS LED Hardware Indicators...

  • Page 17: Chassis Grounding Screw

    The cRIO-9082 provides a chassis grounding screw. NI cRIO-9081 1. Chassis Grounding Screw For EMC compliance, you must connect the cRIO-9082 to earth ground through the chassis ground screw. Use wire that is 1.31 mm (16 AWG) solid copper wire with a maximum length of 1.5 m (5 ft).

  • Page 18: Internal Real-Time Clock

    CMOS BATTERY IS DEAD battery is dead. The cRIO-9082 still starts, but the system clock is reset to the date and time of the BIOS release. The battery is not user-replaceable. If you need to replace the CMOS battery, contact NI.
  • Page 19 You can also mount the cRIO-9082 in other orientations, on a nonmetallic surface, on a 35-mm DIN rail, on a desktop, or in a rack. Mounting the cRIO-9082 in these or other configurations can reduce the maximum allowable ambient temperature and can affect the typical accuracy of modules in the cRIO-9082.

  • Page 20: Mounting Requirements

    Mounting Requirements Your installation must meet the following requirements for cooling and cabling clearance. Allow 50.8 mm (2.00 in.) on the top and the bottom of the cRIO-9082 for air circulation, as shown in the following figure. Figure 6. cRIO-9082 Cooling Dimensions...

  • Page 21: Ambient Temperature

    Ambient Temperature Measure the ambient temperature at each side of the cRIO-9082, 63.5 mm (2.50 in.) from the side and 50.8 mm (2.00 in.) forward from the rear of the cRIO-9082, as shown in the following figure. Figure 8. cRIO-9082 Ambient Temperature Location 50.8 mm...

  • Page 22: Surface Mounting Dimensions

    Fasten the cRIO-9082 to the surface using the M4 screws appropriate for the surface. Screws must not exceed 8 mm of insertion into the cRIO-9082. Tighten the screws to a maximum torque of 1.3 N · m (11.5 lb · in.).

  • Page 23: Mounting The Device On A Panel

    Mounting the Device on a Panel You can use the NI panel mounting kit to mount the cRIO-9082 on a panel. What to Use • cRIO-9082 • Screwdriver, Phillips #2 • NI panel mounting kit, 781919-01 – Panel mounting plate –...

  • Page 24: Panel Mounting Dimensions

    (7.43 in.) (4.29 in.) 58.2 mm (2.29 in.) Mounting the Device on a DIN Rail You can use the NI DIN rail mounting kit to mount the cRIO-9082 on a standard 35-mm DIN rail. What to Use • cRIO-9082 •...

  • Page 25: Mounting The Device On A Desktop

    Align the cRIO-9082 and the DIN rail clip. Fasten the DIN rail kit to the cRIO-9082 using the screwdriver and M4x10 screws. NI provides these screws with the DIN rail mounting kit. Tighten the screws to a maximum torque of 1.3 N · m (11.5 lb · in.).
  • Page 26 2. Adapter brackets (x2) 3. M4x10 screws (x6) What to Do Complete the following steps to mount the cRIO-9082 on a desktop. Use a #1 Phillips screwdriver and the six M4×10 screws to attach the adapter brackets to the chassis.
  • Page 27 Figure 12. Attaching the Adapter Brackets to the cRIO-9082 Align one of the end brackets with the mounting hole at one of the ends of the chassis. 26 | ni.com | NI cRIO-9082 User Manual Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 28: Desktop Mounting Dimensions

    Repeat steps 2 and 3 to attach the other end bracket to the other end of the chassis. Desktop Mounting Dimensions The following figures show the desktop mounting dimensions for the cRIO-9082. Figure 14. cRIO-9082 Desktop Mounting Front Dimensions 28.2 mm 28.1 mm...

  • Page 29: Bios Configuration

    BIOS Configuration Resetting the System CMOS and BIOS Settings The cRIO-9082 BIOS configuration information is stored in a nonvolatile memory location that does not require a battery to preserve the settings. Additionally, the BIOS optimizes boot time by saving specific system information to memory backed up by a battery (CMOS).
  • Page 30 Reset the DIP switches to their normal positions. Power-On Self Test Warning Messages The cRIO-9082 POST displays warning messages for specific issues onscreen. You can use MAX to enable Console Out to send these warning messages through the RS-232 serial port.

  • Page 31: Bios Setup Utility

    This warning indicates that the BIOS settings have the default values. • Warning: Recovering from CPU Overtemp—This warning indicates that the thermal protection features of the cRIO-9082 shut down the system because of a high CPU temperature. • Warning: Recovering from Ambient Overtemp—This warning indicates that the thermal protection features of the cRIO-9082 shut down the system because of a high ambient temperature.

  • Page 32: Main Setup Menu

    The Advanced setup menu contains BIOS settings that do not require modification for normal operation of the cRIO-9082. If you have specific problems, such as unbootable disks or resource conflicts, you may need to examine the settings in this menu.

  • Page 33: Sata Configuration Submenu

    C-States—This setting enables or disables CPU power management. The default value is Disabled when booting LabVIEW Real-Time, Enabled when booting other OSes. 32 | ni.com | NI cRIO-9082 User Manual Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 34: Video Configuration Submenu

    DC power is lost. Valid values are Stay Off and Turn On. The default value is Turn On. When set to Stay Off, the cRIO-9082 returns to the soft off power state after AC power is restored. When set to Turn On, the cRIO-9082 powers on when DC power is restored.
  • Page 35 Device Settings—This item displays the current base address and interrupt request level (IRQ) information for the onboard RS-232 serial port. 34 | ni.com | NI cRIO-9082 User Manual Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 36: Serial Port Console Redirection Submenu

    Change Boot Config on Next Boot—This setting temporarily overrides the combined state of the LABVIEW RT and SAFE MODE switches. This setting selects whether the NI cRIO-9082 User Manual | © National Instruments | 35 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 37: Labview Rt Configuration Overrides Submenu

    Real Time system. • CPU Hyper Threading (NI cRIO-9082 Only)—This setting allows overriding the optimal configuration for Intel Hyper-Threading technology when booting LabVIEW RT. The default value is Use RT Default.

  • Page 38: Boot Settings Configuration Submenu

    CD/DVD ROM Drive BBS Priorities Submenu The CD/DVD ROM Drive BBS Priorities submenu specifies the boot priority of CD/DVD ROM drive devices. NI cRIO-9082 User Manual | © National Instruments | 37 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...

  • Page 39: Security Menu

    The Save & Exit setup menu includes the following settings: • Save Changes and Reset—This setup utility then exits and reboots the cRIO-9082. Any changes made to BIOS settings are stored in NVRAM. The <F10> key also selects this option.

  • Page 40: Worldwide Support And Services

    NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas, 78759-3504. NI also has offices located around the world. For telephone support in the United States, create your service request at ni.com/support...
  • Page 41 . You can find information about end-user license agreements (EULAs) ni.com/patents and third-party legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/ for the NI global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other legal/export-compliance import/export data.
  • Page 42 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...

Table of Contents